The application of waste paper baler has many advantages. The choice of using waste paper baler can reduce the production cost, the packaging speed is relatively fast, etc. It is beneficial to clean and maintain in time after selecting the waste paper baler. Long-lasting application of equipment. Now Nick wants to introduce you to the scope of application of the waste paper baler and the benefits of choosing it.

The main machine adopts high-quality steel, super wear-resistant steel plate is strictly welded according to the process. The hydraulic system adopts domestic famous brand parts and some key components are all imported. The motor adopts Siemens energy-saving motor/Japan Mitsubishi original PLC. It has the characteristics of rigidity, good wear resistance, high service life, safety and energy saving, accurate operation, convenient operation and maintenance, etc., which effectively improves work efficiency, reduces labor intensity and reduces production cost.

Automatic waste paper baler
1. Mainly applicable to: packaging of loose materials, such as waste paper edge, carton and other compression packaging.
2. Hydraulic configuration: low noise hydraulic circuit system, using imported high-quality components, not only to ensure the quality but also improve the packing speed, the performance of the whole machine is stable
3. Electrical configuration: PLC control is adopted, the failure rate is low, and the inspection and elimination are simple and fast.
 4. Shearing knife: The imported universal scissors design is adopted to improve the cutting efficiency and extend the service life of the blade.
5. Wire tying device: The latest international wire tying device saves wire, fast binding, low failure rate, easy cleaning, maintenance and repair.
6. Conveyor: The conveyor belt adopts new PVC material, which is resistant to corrosion and aging; it has the advantages of non-slip, large conveying capacity and strong load capacity.
7. The length is freely set and the packed value is accurately recorded.
8. Easy installation, simple foundation construction, no need for foundation reinforcement.
9. Feeding mode: optional air suction feeding, conveyor belt feeding, direct feeding

2019-03-04

The automatic waste paper hydraulic baler is believed to be very familiar to everyone. Nick Baler will introduce the impact of the automatic waste paper hydraulic baler on the environment.
The automatic waste paper hydraulic baler is very important for the environmental protection cause. We need to make an environmentally-friendly waste paper baler. At present, wood pulp for papermaking is mainly derived from natural forests in China. The large consumption of paper not only causes a sharp decrease in the forest area, but also causes serious pollution of rivers and lakes due to the discharge of sewage from pulp production. The wear of the fully automatic waste paper hydraulic baler within the permissible limits specified by the design becomes normal wear of the waste paper baler. This wear is generally in the initial stage, because the new friction surface has a certain roughness, the real contact surface is small, and the wear is relatively fast, which is called the run and the stage. As the surface gradually flattens and the actual contact area increases, the waste paper baler gradually enters a normal stable wear phase, and the wear of the friction surface is slight and slow and stable.
Many baler manufacturers have seized this opportunity, using high-tech achievements, gradually improving the performance of fully automatic waste paper baler equipment, and developing more comprehensive equipment, showing its obvious advantages, let more Users are getting more and more recognized!
Although we have made great progress in production technology through the joint efforts of manufacturers of fully automatic waste paper hydraulic balers, we cannot be complacent, and the automatic waste paper hydraulic baler has a very large upside, so we We must continue to learn advanced production technology and advanced production concepts at home and abroad to create more professional automatic waste paper baler equipment. The oil leakage of the fully automatic waste paper hydraulic baler is more serious. If the oil pump pressure is adjusted too high, the wear of the moving parts will increase the sealing gap, the sealing device will be damaged, and the viscosity of the oil used in the waste paper hydraulic baler will be too low, which will increase the leakage. After identifying the cause, take appropriate measures to eliminate it.

2019-03-03

With the increasing awareness of environmental protection, the hydraulic baler plays a big role. It can reuse some waste paper, and it is more and more popular with everyone. Our company's hydraulic waste paper baler has been continuously researched and developed. Innovation, constantly following the development of some advanced foreign technology, advancing with the times, to create the most practical, most assured, most advanced hydraulic packaging machinery for domestic environmental protection.

The company insists on perfecting and deepening quality management Keeping pace with the times The first-class quality of the foundry industry~ quality assurance, quality problems in one year warranty, replacement, return and bear the packaging and transportation costs of accessories. Welcome new and old customers to purchase ~ Let's take a look at the operation process of the hydraulic waste paper baler:
1. This is mainly used for the packaging and use of waste paper, and the operator must operate according to the operating procedures.
2. Check the circuit for misconnection or leakage before starting the hydraulic pump.
3. If abnormality is found, stop the operation immediately and eliminate the cause.
4. Hydraulic fluid must be added to the specified oil level line (46# hydraulic oil) before use.
5. When packing, the operator must pay attention to safety, evenly spread the paper, and place the paper in place. The upper lid door should be closed to start packing.
6. When packing, the hydraulic handle should be quickly pushed to the specified position to prevent the hydraulic handle from being quickly pushed to the specified position when the valve is packed. When the package is taken, the hydraulic handle should be quickly pushed to the specified position and the hydraulic oil flow is not enough, resulting in the motor passing. The flow causes the motor to overcurrent. Blockage and insufficient hydraulic oil flow cause the motor to over-current.
7. When the cover cylinder handle is pulled to the return position, the reverse handle is pushed.
8. All hydraulic rods must be retracted into the hydraulic cylinder after packing to prevent dust from damaging the seal and leaking oil.
9. Every anti-package around the hydraulic reverse board should be cleaned in time to prevent jamming.
10. Regular maintenance work should be done, and the oil pipe should be found in the place where it leaks.
11. When adjusting the pump, valve and pressure gauge, it must be carried out by experienced technicians. If the pressure gauge is found to be faulty, it should be repaired or replaced immediately.
12. Do not know the main machine structure, performance and operating procedures. When multiple people operate at the same time, the division of labor should be clear to avoid the danger of misuse.
13. After the door is opened, it is strictly forbidden to operate the door to prevent accidents.
14. When running or packing, do not repair or touch the moving parts by hand. Do not press the material in the bin with your hands or feet.
15. Nick baler waste paper baler oil pressure: no pressure adjustment is allowed, the operator must work under the oil pressure, the highest pressure limit 30MPa.
16. The oil in the tank must be strictly filtered and always maintain a sufficient amount of oil. The tank should be cleaned and replaced once every six months.
17. Lubrication should be filled at least once a day as required, and the debris in the chamber should be cleaned once per shift.
18. Stop the machine immediately if there is a serious oil leak or an abnormality in the work. Do not look at the place where the oil is sprayed. Do not directly block it by hand. Do not force the disease to run.
19. Use 46# anti-abrasion oil, always pay attention to oil temperature, stop when it exceeds 75 degrees.

2019-02-26

There are many types of hydraulic waste paper balers, but we also have a lot of things to pay attention to during the process of use, which are mainly divided into the following aspects:

First, the hydraulic baler must first use the extension cord section, and the area should be calculated according to the motor power of the hydraulic baler. Do not touch the power distribution box with wet hands, there is a risk of electric shock. Secondly, when packing water or wet items, a leakage protector should be installed to protect it. Always use gloves, protective glasses, and a mask when installing or packaging. If not used, it may cause injury or health hazard.

Third, the machine is a baler that uses a strap on the packaged object. Do not use for other purposes. Packaged items are items that need to be packaged. Do not put your hand or body close to the main unit. Do not remove parts such as panels, covers, doors, etc. when using the machine. When the parts are removed, not only will the machine malfunction, but it will easily lead to ginseng accidents. Finally, the power capacity of the hydraulic baler should ensure sufficient capacity, the motor capacity is greater than 5.5KW, the plug and the socket are not easy to generate arc, and there is a danger of fire. The ground terminal must be connected to the ground wire. The grounding resistance must be less than 4 ohms. There is a risk of electric shock when it is not connected to the ground wire or is not fully connected.

2019-02-25

The disassembly of the waste paper baler hydraulic cylinder requires professional operation. After the disassembly, the price of the straw baler should first check the appearance of each part of the hydraulic cylinder. According to experience, it can be judged which parts can continue to be used and which parts must be replaced and repaired.

1. The inner surface of the cylinder. The inner surface of the waste paper baler cylinder has a very shallow line-like frictional injury or a point-like flaw, which is allowed, and it is useless.

If there is a vertical strain, even if a new piston seal is replaced, it is impossible to prevent oil leakage. The inner hole must be ground, or it can be corrected with fine sandpaper or oil stone. When the longitudinal strain is deep and cannot be corrected, the new cylinder must be replaced.

2. The sliding surface of the piston rod. When a longitudinal strain or a scratch occurs on the sliding surface of the piston rod that slides relative to the sealer piston rod sealing ring, the judgment and treatment method are the same as the inner surface of the cylinder. However, the sliding surface of the piston rod is generally hard chrome plated. If a part of the plating layer is peeled off due to wear and a longitudinal flaw is formed, the oil leakage at the piston rod seal has a great influence on the operation. The old coating must be removed, rechromed and polished. The chrome plating thickness is about 0.05mm.

3. Sealed. Piston seals and piston rod seals are key components to prevent oil leakage inside the waste paper baler hydraulic cylinder.

When inspecting the seal, first observe the damage of the lip of the seal and the wear of the seal friction surface. When it is found that there is a slight scratch on the lip of the seal and the friction surface is slightly worn, it is better to replace it with a new one. Seals that have been used for a long time and whose materials are hardened and brittle must also be replaced.

2019-02-24