WhatsApp:008615021631102      Email:sales@nkbaler.com       TEL:86-29-86031588

News Center

You Position : Home >> News Center
  • Matters needing attention in the process of installing the hydraulic oil pump of the waste paper baler:

    1.The installation height,length and diameter of the suction pipe of the oil pump should meet the calculated values,strive to be short and reduce losses (such as elbows, etc.);and ensure that the pump does not exceed its allowable cavitation allowance when it is working.The inner diameter of the oil suction pipe should not be less than the specified requirements.The suction pipe should not be too long.The 90 degree bend should not exceed two.It is connected to the inlet of the oil pump with a soft short connection.The installation height of the oil pump should be such that the hydraulic oil can flow to the suction port of the oil pump.

    2.The quality of the oil pump installation has a very important impact on the smooth operation and service life of the pump,so the installation and correction work should be carried out carefully and not rashly.The support or base of the hydraulic pump must be strong and firm,and the pump shaft of the hydraulic pump must be well aligned with the motor.
    3.The place where the oil pump is installed should be spacious enough to facilitate maintenance work.
    4.The suction and discharge pipelines of the oil pump should have brackets,which are not allowed to bear the load of the pipeline.
    The waste paper baler has brought a lot of convenience to our lives,and we have also made the greatest improvement in its performance as much as possible.The waste paper baler can exert its maximum function and continuously improve the work efficiency of customers.
    2020-09-08
    Share:
  • The straw baler is applied to corn stalks,wheat stalks,rice straw,sorghum stalks,fungus grass,alfalfa grass and other straw materials.It also protects the environment,improves the soil,and creates good social benefits.
    Operation steps of straw baler
    1.Raw material crop straw
    2.Feed into the straw mill or straw rubbing machine for crushing processing
    3.The crushed materials enter the straw baler bin

    4.The material reaches the baling standard(the straw machine or kneading machine continues to feed)


    5.Automatic control cabinet,one key to start packing
    6.Bagging and packaging
    Nick’s company has more types of straw baler,you can open our company’s website www.nkbaler.net to choose,or call our company’s phone 86-29-86031588
    2020-09-08
    Share:
  • This kind of large hydraulic baler is widely used in the green and dry storage of forage grass in animal husbandry.It can save storage space and extend the feeding time of green straw.After packaging and sealing,it will naturally ferment to produce probiotics,beneficial bacteria,lactic acid bacteria,and protein,which will be naturally fermented.Cattle and sheep and other livestock are easily absorbed after feeding,and the growth rate will increase 2%,which greatly reduces the cost of feed transportation and storage,and reduces the labor intensity of workers.It has brought tangible economic benefits to the animal husbandry industry.It is one of the products required for silage reclaiming of medium and large breeding plants.


    This kind of straw baler is mostly used in large farms.Users who do yellow storage and dry storage can use a three-cylinder hydraulic baler,and the effect is better.
    There are more types of straw balers,you can open our company's website www.nkbaler.net various types of straw balers for your choice.Or call our company for consultation 86-29-86031588
    2020-09-08
    Share:
  • 1.No-load test machine
     Turn on the power of the waste paper hydraulic baler,loosen the system overflow valve to make the system overflow safely,start the motor,and observe whether the rotation of the motor is consistent with the sign of the oil pump.Start the motor and observe whether the oil pump is stable and reliable during operation.If there is no noise in the pump,if there is no noise,it can be tested.Gradually adjust the overflow valve handle of the waste paper baler to make the pressure value about 8Mpa.Operate in order to single-act each cylinder to observe whether the operation is stable,and adjust the main pressure cylinder,side pressure cylinder,bottom plate and side frame.For parallelism,fix the main pressure cylinder and the side pressure cylinder,and use the adjusting support to support the tail of the cylinder.
    2.Load test machine
    (1)The load test can be performed after the operation of the single cylinder is familiar.

    (2)Adjust the pressure of the waste paper hydraulic baler system to make the pressure display value about 20~26.5Mpa,and tighten the nut.Do several packing sequences in the order of operation.Feed material to the compression chamber.The load test adopts the form of physical packaging.Press 1~2 bales and keep the pressure for 3~5 seconds after the stroke of each waste paper hydraulic baler cylinder is in place.Perform a pressure test on the system and observe if there is any If there is oil leakage,remove it after the system is depressurized.

    The two methods mentioned above are the two methods often used by Nick Baler.If you don’t understand during the detection process,please call us:86-29-86031588.
    2020-09-08
    Share:
  • Advantages of plastic bottle packing machine:The hydraulic oil circuit power system is selected,which greatly improves the packing power.It has the characteristics of fast packing speed,high power,energy saving and power saving,and stable function;a variety of cooling systems are available for users to choose (water cooling system,Air-cooled system and industrial air-conditioning cold system;two fast and efficient wire binding methods,push wire and hook wire are selected,fast and efficient wire binding equipment,low fault rate and easy maintenance.

    Nick is here to remind the majority of business friends that no matter how good the equipment is,it requires the correct operation of the personnel,Good equipment is nothing more than a low rate of its own faults,no faults on its own,and more tolerant of over-contract cooperation,but it also cannot withstand long-term illegal operations.Therefore,the stable production is obtained through the correct operation and protection of the equipment.If the operation is improper and the operators are not trained,accidents may occur even with higher-level equipment.
    2020-09-07
    Share:
Shaanxi Nick Machinery Equipment Co.,LTD 
TEL: 86-29-86031588
Fax: 86-29-86031588 Sitemap
Add: East Qunsheng Road Wuxi City,Jiangsu,China

Email:info@nkbaler.com Nickbaler888@gmail.com 

WhatsApp: 008615021631102  

Copyright © NKBALER .rights reserved sitemap.html
Message
go back to the top