1.When we remove the upper panel,we must first cut off the power switch,unplug the power supply,and then repair and adjust the plastic bottle baler machine.
2.During the operation of the machine,it is forbidden to put your hands or head into the frame.If you put your head or hands into the frame,it will cause harm to your body.

3.Pay attention to some matters when using electrical components,such as turning off the power switch and unplugging the power plug when repairing or adjusting the plastic bottle baler machine.When the power is turned on,touching the electronic control box and transformer with your hands will cause electric shock.In addition,the external insulation is damaged,and contact with the body may cause an electric shock accident,which is very dangerous.

4.Regarding the heater,if the heater is in a high temperature state (about 230 degrees),if you touch it directly with your hands,you will get burned.After cutting off the power,we have to cool down for a period of time before returning to normal temperature.
Nick Machinery reminds you that safe production is the first priority.The plastic bottle baler machine produced by our company is easy to operate,easy to maintain,safe and energy-saving,and can better serve you.
Nick Company:www.nkbaler.net,or call: 86-29-86031588

2020-10-20

Nick Machinery uses high technology to design the whole machine with dual-circuit control,which is more stable and reliable than the previous single-circuit control performance.The dual-circuit control reduces the internal load of the machine's electrical board,and the baler Press structure runs smoothly and stably between each circuit.
So what are the requirements of the baler Press for the use of oil?
1.In places where fire prevention is required,the ignition point of thick oil should be high;in places with cold climate,the freezing point of oil should be low.
2.The oil should not be easily oxidized to avoid the occurrence of gum and asphaltene due to oxidation,which may cause the oil to degenerate.Impurities composed of oxides can also block the oil circuit and damage the normal operation of the hydraulic system.

3.It has no effect on human health.

4.Clean quality and no impurities.

5.It has outstanding smooth function.In the hydraulic system of the baler Press,the working fluid is not only used to transfer energy,but also has a smooth effect on the conflicting surfaces of the hydraulic components.In some machine tools,the oil source of the machine tool lubrication system comes from the hydraulic system,and the hydraulic system uses the same oil pump to supply oil.Therefore,hydraulic oil should have high oil film strength and outstanding smoothing function within the operating temperature and pressure change scale to avoid dry conflict.

The packer produced by Nick baler Press is recognized by many customers with high-quality qualifications and professional craftsmanship according to everyone's actual needs and is trustworthy.

WEB:www.nkbaler.net,TEL:86-29-8631588

2020-10-20

The horizontal waste paper baler Press is a kind of equipment that can pack and bundle waste paper items.However,the horizontal waste paper baler Press often leaks when it is working,so the horizontal waste paper baler Press mainly leaks What are the reasons for it?

1.The sealing ring of the cylinder of the horizontal waste paper baler Press is damaged.The downward pressure of the cylinder is driven by the air source in the cylinder to push the cylinder downward,but when the sealing ring in the cylinder is damaged,the cylinder cannot form a sealing effect. At this time,the cylinder will leak air,and then the horizontal type The waste paper packer cannot work properly.

2.The solenoid valve is leaking.The solenoid valve of the horizontal waste paper baler Press is a linking device between the intake pipe and the cylinder.Although it is not part of the cylinder,its function is also the same.When the solenoid valve is used for a long time,air leakage will also occur.
3.The triple parts are damaged.
Therefore,we must carefully check during production and pay attention to the daily maintenance of the baler Press.
If you are interested in the waste paper baler Press or have any questions,please log on the website of Nick Company: www.nkbaler.net, or call: 86-29-86031588

2020-10-19

The purpose of the scrap steel shearing machine:It is used for cold shearing of scraps such as round steel,square steel,angle steel,I-beam,plate steel,steel pipe,etc.,cut-to-length shearing of hot-rolled small steel,and steel rolling Cut-to-length of factory-shaped steel,etc.
Advantages of scrap steel shearing machine:
1.Reasonable design structure:Reasonable use of lever principle,crocodile mouth structure,stronger bite force than traditional flat shears,and lower power consumption.

2.High safety factor:The shearing work must be carried out after obtaining the pressure cylinder work program.The scrap steel shearing machine has two cylinders,one is the main pressure cylinder,which is responsible for the shearing work,and the other is the pressure cylinder.Responsible for compacting the shearing material.Simply put,the shearing cylinder can work only after the material pressing cylinder is in place to prevent shaking,jumping,splashing and other conditions of the sheared material.Sequence control is more secure.

3.Hydraulic drive:smooth cutting,low noise, easy installation,no foundation required,high-quality high-pressure oil pump for oil supply,stronger stability.
4.Fast shearing speed:using large-diameter high-quality hydraulic valve block,no leakage,large flow,installation of return acceleration device,after the material is cut,the shearing cylinder accelerates when it returns,thereby increasing speed and efficiency.
5.The quality of the blade is good:the use of high-quality high-hardness alloy materials and special processing technology ensure that the normal service life of the blade is twice that of the counterpart products.
Nick brand the scrap steel shearing machine operation is simple,and the package is automatically delivered,which improves work efficiency.The installation of emergency stop settings makes the operation safer.

2020-10-19

Technology is advancing,and the machinery and equipment of scrap bailer presss are also being upgraded.
Scrap bailer presss have also been manually tightened from the most preliminary,and later semi-automatic bailer presss have been developed to fully automatic bailer presss in recent years,and they have quickly become mainstream equipment in the market.
Automation also reduces many harms caused by human operation.So,what are the advantages of fully automatic hydraulic bailer press?
1.Fully automatic hydraulic bailer press is more efficient than manual and semi-automatic bailer press,and it also reduces the labor intensity of workers.

2.The density of bales produced by the automatic hydraulic bailer press is greater.Save transportation costs.

3.The printed package has a more regular appearance and is not easy to open.It can also improve the technical strength and corporate image of Nickelodeon.
4.Due to the high density of waste products packed into the hydraulic bailer press.Less pollution to the environment.
Nick brand automatic scrap iron bailer press has simple structure,stable work,automatic bale delivery,low failure rate and easy cleaning and maintenance,which can better serve you.

2020-10-16