1. It is necessary to conduct regular monthly inspections of all parts of the equipment, including the transmission parts and cylinders. We need to check the looseness of the screws or nuts in each part in detail.
2. Regularly clean up the horizontal waste paper baler to remove all the remaining waste paper materials. It is important to note that in order to ensure the safety of humans and machines, we must ensure that the power supply is disconnected when cleaning up the waste paper baler. And use a relatively clean cloth to wipe. Also pay attention to the lubrication and maintenance of the transmission system and the parts of the end seal bearing.
Waste paper baler

1. The waste paper baler should be well fixed during installation: because the machine is running fast, uneven ground may shake the machine in vibration and cause safety hazards to the operators. Therefore, the ground must be kept flat, and the machine must be installed according to the instructions to keep the machine stable. When the machine is running, it is prohibited to touch the moving parts of the machine with your hands.  
2. Electrical safety of the machine: ground the power supply of the machine to avoid electric shock caused by improper operation. There must be an automatic shutdown device for the power supply, so that the machine can automatically stop when there is an electricity problem to avoid electric shock and other conditions.   

3. The cleaning of the machine: the waste paper baler often uses packaging cartons, etc., so it will be blocked by debris after a long time. Sometimes it will cause the machine to run poorly, cause damage to the machine, and reduce the service life of the machine. The machine should be cleaned regularly, and lubricating oil should be regularly applied to the parts that need lubricating oil.  

4. The operator of the machine should do a good job of protection, such as wearing gloves, and prohibiting the head and hands from reaching the inside of the machine. Non-machine operators should keep a distance from the machine as much as possible to prevent damage caused by material splashing. 
5. Check the machine before use, and run it for a while: after use, turn off the switches according to the steps.  
6. Do not disassemble the protective cover of the machine at will: It is prohibited to disassemble the protective cover during the operation of the machine, and non-operators or technicians are not allowed to disassemble the protective cover of the waste paper baler at will.

2020-08-11

After the busy farming period, a lot of crop stalks are piled up on the countryside and roadsides, occupying too much storage space, and it is not environmentally friendly or hygienic. In winter, it is a kind of fire and it is a serious fire hazard. The hydraulic straw baler is used to pack these straws, these unfavorable factors are completely solved, and the long-term troubles of these problems in the production and life of farmers are eliminated. It is an effective tool to reduce the burden on farmers and change the rural environment.

The Nick Company hydraulic straw baler puts the straw into the feed port and then hydraulically compresses it. When the straw reaches a certain density in the fuselage, it will be automatically squeezed out, so that the straw bales are not scattered, and the formed straw bales are small and compact. It is compact, and the straw bales are loose inside and outside, with good air permeability, which is convenient for transportation and storage. Since the promotion and use of this machine, it has played a huge role in solving the pollution caused by straw recycling, rural straw burning, and straw utilization. The baled straw is convenient for loading and unloading and transportation, and the carrying capacity is increased by 2-3 times, which can save labor and transportation costs by more than 50%. It solves the inconvenience caused by ultra-high and ultra-broadband in transportation. It is deeply loved by farmers. It is a good helper for our farmer friends to make a fortune.For more information ,please visit: www.nkbaler.net

2020-08-07

1. Steel structure frame, rail steel baffle, high strength and sturdiness, upper-mounted two-way oil cylinder, simple installation, no foundation required, no site conditions restrictions, and convenient use.

2. Hydraulic drive, low noise, high pressure, stable operation and no vibration, this machine is equipped with fast and slow speed gears, the speed of light load return is 2.25 times of the press-in speed, which saves production time and greatly improves work efficiency.

3. According to different materials, the machine can be divided into three-door, four-door, five-door, six-door and other shapes, and it can be bundled and packaged in the shape of a well.
4. This machine adopts high-performance hydraulic circuit, which saves electricity by 33% compared with similar products. Imported hydraulic accessories make the whole machine superior in performance.
5. Self-designed shearing device improves shearing efficiency. The blade is made of wear-resistant materials and has a long service life.
6. Microcomputer PLC control is optional, and the packing length can be set by yourself, automatic binding, fast binding speed, low failure rate, easy to pack.
7. The lower hopper can be equipped with automatic spraying device and dispersing device.

8. The conveyor belt is controlled by computer, with large conveying capacity, abrasion resistance, strong load capacity and anti-skid function.

9. Bundled pieces of special specifications and sizes can be customized according to customer requirements.
10. Good equipment for labor efficiency, labor intensity, manpower saving, and transportation costs.
Advantages of hydraulic straw baler:
1. Avoid the pollution caused by farmers from burning straw.
2. This is a new resource which increases the income of farmers. The straw bales are easy to sell and the sales volume is large.
3. Reasonable use of resources. Bundled wheat stalks, corn stalks, millet stalks, rice straws, etc. can be used well, such as processing livestock and poultry feed, manufacturing fiber board, producing biogas and papermaking.
4. Promote the development of related downstream industries and provide a large amount of raw materials for related downstream industries, which can save resources, improve resource allocation, and achieve civilized and environmentally friendly agricultural production.for more information ,please visit :www.nkbaler.net

2020-08-07

Waste paper baler is a rare type of packaging equipment in the food consumer industry. The use of waste paper baler outside of the industry is also very common, easy to use, fast packaging speed, and wide range of packaging applications

1. Turn on the main power switch of the waste paper baler equipment until the white light-emitting tube on the decorative panel lights up, the motor starts to run, and the single chip in the machine starts to work. After about 15 seconds, the heating temperature drops to a certain height, which is about the same time. You can start the packaging process.

2. The waste paper baler can also adjust the length of the belt according to the dimensions of the packaged parts to ensure that the input of the packaging belt is enough to make a circle around the part to be packaged. Clockwise rotation can increase the length of the belt. Otherwise, it is easy to have malfunctions.

3. When the machine is finished, we must remember to close the main power supply and stop the maintenance and repair of the machine body according to the requirements. The waste paper baler is used to squeeze waste paper and similar products under normal conditions. It is also packaged and formed with a public packaging belt to greatly reduce its volume, thereby achieving the purpose of increasing transportation volume, wasting freight, and adding benefits to the enterprise. Introduced advanced technology and advanced technology of similar products from abroad and abroad.
Nick Baler is committed to the production of balers with a complete range of features such as reasonable design, beautiful models, convenient operation, and accurate accuracy. In the future, it will continue to research and innovate to better serve consumers and make consumers more assured.for more information,please visit :www.nkbaler.com

2020-08-07

1. Adjustment of oil supply system:
1.1. Fuel tank refueling: The rules of this system use hydraulic oil above No. 46. When refueling, pay attention to the refueling pipe not to break the filter screen. The refueling fluid must be pure and clean, and the refueling amount is 800-1000 kg.
1.2. Jog the main pump motor start button to check the direction of the motor. If it does not match the direction of rotation indicated on the pump body, the motor wiring should be interchanged so that the rotation direction is the same.
1.3. Start the oil pump motor for 15 minutes without load, adjust the rising height of each plunger during this period, and then acknowledge the normal and complete the mechanical adjustments of the whole machine to perform the following operations. The metal briquetting machine includes metal chip briquetting machine and metal packing The two models of the machine directly cold press various metal scraps through high pressure, which is convenient for storage, transportation and recycling.
1.4. Price pressure, overflow and adjustment of waste plastic baler:
In order to ensure that the pressure oil entering the main cylinder of the baler can maintain the correct flow and pressure, and to maintain the motor from damage due to overload, it is important to adjust the overflow and unloading.
1.5. Adjust the oil pump pressure:
Step on the materials that need to be packed into the bag box, extend the stepping cylinder to position it, turn on the main oil cylinder and raise the valve. The metal briquetting machine includes two types of metal chip briquetting machine and metal baler. Various metal scraps are directly formed by cold pressing, which is convenient for storage, transportation and recycling. Tighten the oil pump relief valve adjustment knob gradually, pack the load, pay attention to investigate the motor current and pressure gauge readings. When the pressure rises to 20-25Mpa, the valve adjustment knob should be fixed, and after unloading, re-check the package from the beginning.
2. Electrical system debugging:

The primary adjustment of the position of the travel switch, the height of the shaft plug ascending, the waste paper baler is used to knead and firm waste paper and similar products under normal conditions, and package them with special packaging tape to greatly reduce the volume, and then reduce the transportation Volume, saving freight, for the purpose of adding benefits to enterprises. The introduction of advanced technology and advanced technology of similar products at home and abroad.

3. Price trial run of waste plastic baler:
After the above operations are adjusted, you can energize and test the empty car, move the multi-way reversing valve to perform the self-locking actions of the main oil cylinder and the door, and repeat several times to see if it is correct.
The load can be packaged after the various actions of the power-on test and empty car inspection meet the requirements. When the load is packed, the upper limit of the oil pressure gauge should be investigated and adjusted to 20-25Mpa to maintain the motor and pump valve system.

Finally, let's talk about the price of hydraulic baler. Its price depends primarily on its type, use, and market development!

Nick Baler is committed to the production of balers with a complete range of features such as reasonable design, beautiful models, convenient operation, and accurate accuracy. In the future, it will continue to research and innovate to better serve consumers and make consumers more assured.

2020-08-07