Nick brand waste paper baler is easy to operate, safe and energy saving, it is your best helper
The last article talked about what the gear pump of the waste paper baler is. Now Nick Machinery will tell you the precautions for the installation of the gear pump.
1. When replacing and installing the gear pump of the waste paper baler, first distinguish the direction of the oil inlet and outlet of the oil pump, and it cannot be installed reversely. The center height and concentricity of the main shaft of the transmission motor (or internal combustion engine) and the oil pump should be the same, and the installation deviation should not be greater than 0.1mm. At the same time, there should be an axial gap at the shaft ends to prevent collisions during axial movement. Generally, flexible couplings should be used.

2. The installation position of the pump relative to the height of the fuel tank should not exceed the specified oil suction height, generally should be less than 0.5m. The suction pipe of the pump should not leak air. The suction pipe should not be too long or too thin, and the elbow should not be too many.

3. The viscosity and oil temperature of the hydraulic oil of the waste paper baler system should be selected according to the brand specified in the sample or regulations. The working oil temperature is generally around 40 degrees.
4. When the oil pump is started, start it with no load for several times. If the air is not drained, the pump will produce vibration and noise. At this time, the connection of the oil outlet should be slightly loosened, so that the gas in the pump is completely removed and the movement is stable. Then, slowly load and run from no-load until it is stable before it can be put into normal operation.
5. After the hydraulic oil pump of the waste paper baler enters into work, it is necessary to check the operation of the pump frequently. If any abnormality is found, the cause should be found out immediately and the fault is eliminated.

The working oil of the gear pump should also be checked regularly, and the hydraulic oil of the waste paper baler is usually tested every 3 months.

If you are interested in the above waste paper baler or have questions, please log on to our company's website: www.nkbaler.com, or call: 86-29-86031588

2021-01-22

The Nick brand hydraulic baler is recognized by many customers with its high-quality qualifications and professional craftsmanship according to everyone's actual needs and is trustworthy.
In today's society, people have a deeper and deeper understanding of noise, and it is imperative to reduce the noise of hydraulic equipment. The hydraulic pump is one of the main noise sources of hydraulic equipment. The research on the noise fundamentals of hydraulic pumps has attracted wide attention at home and abroad.
The noise of hydraulic pumps can be divided into three aspects: hydraulic noise, mechanical vibration noise, and liquid-gas mixed noise. What is the cause of sudden noise in the plunger pump during use?
1. The inherent noise of hydraulic plunger pumps
2. Cavitation noise
3. Mechanical noise
4. Sudden noise
5. The noise generated by the hydraulic plunger pump after maintenance
6. The hydraulic plunger pump makes noise after replacing the hydraulic oil

7. Gradual noise

These seven aspects are the source of noise generated by the plunger pump of the hydraulic baler, and the maintenance personnel can repair it after confirming the cause of the noise.
Nick Machinery provides: hydraulic baler, automatic hydraulic baler and other packaging equipment, company website: www.nkbaler.net, telephone: 86-29-86031588, look forward to long-term cooperation with you!

2021-01-22

Nick brand waste paper baler has simple structure, stable action, simple operation, low failure rate and easy cleaning and maintenance. It is a good helper for your production.
The machine has been running for a long time, and there will always be various faults. Many people don’t know how to solve it. Our maintenance personnel at Nick Machinery, combined with their years of maintenance experience, put forward a set of query techniques to determine the specifics. Where is the problem?
1. Ask the equipment operator to understand the operating status of the equipment.
2. Ask whether the hydraulic pump is abnormal.

3. Ask about the replacement time of hydraulic oil, filter, etc.

4. Ask whether the pressure or speed regulating valve has been adjusted before the accident and what is abnormal.
5. Ask whether the seals or hydraulic parts have been replaced before the accident.
6. Ask about any abnormalities in the system before and after the accident.
7. Ask what faults often occurred in the past and how to eliminate them.
The maintenance personnel can make a judgment on the location and cause of the fault through simple inquiries, combined with their own actual experience, and propose corresponding solutions.
For more information about waste paper hydraulic parameters and maintenance methods, please log on to the Nick Machinery website www.nkbaler.net, Tel: 86-29-86031588, best-selling models: NKW160Q, NKW200Q, and support custom-made various models of balers, welcome arrival.

2021-01-16

Simple diagnosis technology is to rely on maintenance technicians to use simple diagnostic instruments and personal practical experience to diagnose the faults in the hydraulic system of the waste paper baler, identify the cause and location of the fault, and propose corresponding troubleshooting methods.

Simple diagnosis technology is a commonly used method, among which checking is the easiest one. Which aspects should be checked specifically? Listen to Nick Machinery’s explanation
1. Look at the actual working status of the hydraulic system.
2. Look at the pressure value and fluctuation phenomenon of each measuring point in the hydraulic system.
3. Check whether the oil is clean and deteriorated, whether there is foam on the surface, whether the oil volume and oil viscosity meet the requirements, etc.
4. See if there is any leakage.
5. See if there is vibration when the working parts are working.
6. Look at the product quality, judge the working status of the motion mechanism, the stability of the system working pressure and flow.
By looking at these places, you can determine what went wrong, and then prescribe the right medicine.
If you still can't solve it, please log on to the Nick Machinery website to leave a message, the company website: www.nkbaler.net, or call: 86-29-86031588.

2021-01-16

Nick brand automatic waste paper baler has simple structure, stable action, simple operation, low failure rate and easy cleaning and maintenance. It is a good helper for your production.

Nick Machinery specializes in the production and sales of horizontal waste paper balers, metal balers, straw balers, tire balers and other environmental protection equipment. The quality is trustworthy. Today I will discuss with you today that the price factors that restrict horizontal waste paper balers are Which ones?

1. The main steel, most companies use the same steel, there is not much difference.
2. Composition of hydraulic cylinders. The current hydraulic cylinder technology is relatively mature, but some small manufacturers still use some inferior products, and the product price difference is about 10,000 yuan. Conditional equipment now uses air-cooled hydraulic stations, which greatly reduces the high temperature phenomenon in the work of the waste paper baler.
3. Automatic threading rack. According to the different market prices, the market price is about 30,000 to 50,000 yuan.
4. Electrical products, fully automatic computer control system, the price difference is about 10,000 yuan.

The price factors that affect the horizontal waste paper baler are probably the above points. I hope that it can provide some guidance to our customers when they investigate and purchase.

If you need a horizontal waste paper baler, please visit the Nick Machinery website www.nkbaler.net, there are product pictures and videos, please click to watch! Or call 86-29-86031588, if you don’t understand, someone will be responsible for the explanation.

2021-01-16