1. A wide range of feed raw materials, various green feed, green crop straw, melon, vine and vegetable seedlings, high-moisture grains, slag, etc., can be used to make straw balers;
2. High nutritional value; more than 85% of the nutrients in the forage can be preserved, while the prepared hay can only retain 80% of the nutrients even under the best conditions; under poor conditions, only 50-60% can be retained nutrients;
3. High nutrient yield per unit area. Planting feed crops on the same area of land to prepare straw balers has 30-50% higher nutrient yield than harvesting fruit;
4. Not affected by seasons and weather;
5. The production process is simple and requires less labor;
6. Compared with saving hay, making a straw baler occupies a small area;

7. The straw baler has a sour fragrance after microbial anaerobic fermentation, good palatability and high feed intake

Follow NICKBALER, you can learn more skills and tips https://www.nickbaler.net

2022-10-24

The metal powder cake press needs to work every day. In some large factories, it will not be idle even at night. In order to make the metal powder cake press run safely every day, it is necessary to do daily inspections. The cause of the failure can be found and determined. So, how to do the daily inspection of the metal powder cake press .I summarize it for you in three steps:
1. Check whether the screws at the pressure regulators of the flow valve and other pressure valves are loose. If the pressure regulating screw of the relief valve is loose, the working pressure of the system will not reach the predetermined value or the working pressure cannot be established, and the system will not work normally. The loosening of the adjusting screw of the pressure reducing valve will make the outlet pressure less than the predetermined value, so that the pressure reducing circuit cannot work normally.
2. The amount and temperature of oil in the tank. The amount of oil in the fuel tank should always be kept within the normal range, otherwise it should be replenished in time. The grade of the added oil must be the same as that of the system, and it must be tested to meet the specified indicators; the added oil should be filtered, and the filtration accuracy Not less than the accuracy requirements of the system 

3. Oil leakage at various sealing parts and pipe joints. It is inevitable and common for hydraulic systems to leak under working conditions. Leakage leads to a decrease in system pressure, resulting in unstable speed of actuators, wasting oil, consuming energy, reducing efficiency, increasing oil temperature, polluting the environment, and causing fire hazards. The leakage of the system mostly occurs at the fixed seal and the moving seal. The cause of leakage is usually the damage, aging, damage of the seal or the vibration of the loose connecting screw, which should be repaired in time. Leaks under non-working conditions are not allowed.

NICKBALER Machinery warmly reminds you: When using the baler, you should strictly follow the operating instructions. If you want to know more about after-sales maintenance, please contact us at 86-29-86031588

2022-10-21

We all know that the area of waste paper balers varies greatly depending on the model. For example, the common horizontal baler covers an area of 10-200 square meters depending on the model. How can the baler be installed in a small room?
If you want to install it in a small room, we do not recommend installing a horizontal model. You can choose a vertical waste paper baler, which is characterized by a vertical all-in-one machine, a front door type, and a small footprint. It is an ideal model for volume reduction and recycling.
It should be noted that the foundation ground of the hydraulic waste paper baler must be flat, tamped and hard, and its metal substrate must be flat without any deformation. When the ground is soft, a sweeping rod or a backing plate must be used to increase the force surface and stability.

Therefore, if there are friends in need, you can explain the use requirements and site area, and we will recommend the appropriate type of waste paper baler according to the actual situation. If you have other questions, please contact our factory.

For more detailed description of waste paper baler, you can go to NICKBALER Machinery's website: https://www.nickbaler.net, or you can call our sales phone: 86-29-86031588.

2022-10-20

Crocodile shearing machine is suitable for metal recycling companies, scrap steel plants, smelting enterprises, and cold shearing with various shapes of steel and various metal structures. It is a special tool for shearing steel plates. The performance of this tool is relatively .It is better, so the use of crocodile shears can be seen in many fields. However, the crocodile shearing machine has certain operating requirements when it is used:
1. The crocodile shears are operated by people who are not trained by others and should not be used.
2. Before driving, check whether the components are normal and whether the fasteners are firm.
3. Steel parts, cast iron parts, soft metal parts, too thin workpieces, workpieces less than 100 mm and workpieces exceeding the length of scissors are prohibited for annealing.
4. During operation, human body is not allowed to touch the transmission part and edge of the device, and attention should be paid to the safety of surrounding personnel to prevent the material from warping.Cut the material as far as possible into the knife.
5. When the crocodile shearing machine is operating, the operator shall not leave the post, the work should be completed or temporarily leave the post, the power supply should be cut off, and the machine should not be repaired or touched with the moving parts, and it is strictly forbidden to pressurize the material box with hands or feet Material.

6. All lubricating places of crocodile shears should be filled with lubricating oil at least every shift according to the requirements.

NICKBALER Machinery reminds you that in the process of using the baler, you must strictly follow the product instructions and do not ignore some small details to ensure safe and effective production. If you have any other questions, you can go to NICKBALER Machinery's website to learn https://www.nickbaler.net

2022-10-19

The use of hydraulic balers undoubtedly provides us with great convenience. Whether it is a large or small baler, only the correct use can achieve good results. Why is it easy to loose? In fact, this is also a frequently asked question. According to years of experience, it is actually because of a problem with the baling machine belt of the baling machine. Today we will take a look at the specific solutions.
1. First check whether it is the equipment or the reason for the baling machine tape; if it is found that the thickness is uneven, the width is uneven, etc., it means that the baling machine has quality problems, and the unqualified part should be cut off and tested. When the belt cannot be tightened, adjust the elastic button on the baler until the adjusted belt meets the technological standard.
2. The unstable quality of the baling machine belt will also cause difficulty in feeding the belt, or it may not be able to enter the belt directly. If a roll of tape is mostly not up to the quality standard, try a new bundle with a new one.
3. If you find that the strap is not as tight as before during the use of the baler, we can achieve the tightness you need by removing some straps. If it is too loose, then it is best to replace a strap.
4. The loosening of the baling machine belt of the vertical hydraulic baler can be prevented, mainly requiring the operator to be serious and careful. When operating the baler machine, you should pay more attention to observation, and when the equipment has abnormal noise, you should pay attention to it.
5. The baling machine belt is very important for the baling machine. After purchasing the baling machine, we must also choose the appropriate baling machine belt, so as to ensure the normal use of our machine. Therefore, the quality of the baling machine belt determines whether the baling machine can be used normally or not. .

NICKBALER reminds you: When using, be sure to follow the instructions of the baler for effective and correct operation, so that many failures of the baler can be effectively avoided.

If you are still unclear, you can continue to pay attention to our website https://www.nickbaler.net, and you are welcome to contact us at any time to answer your questions, thank you for reading.

2022-10-18