WhatsApp:008615021631102      Email:sales@nkbaler.com       TEL:86-29-86031588

News Center

You Position : Home >> News Center
  • China automatic waste paper baler manufacturers. Nick Machinery Factory takes products as the leader, capital as the link, and our factory culture as the core, covering various kinds of hydraulic equipment such as waste paper balers and waste plastic balers; mesh belt conveyors, chain conveyors, etc. device. How to repair the waste paper baler hydraulic pump of Nick Machinery Factory: Waste paper baler In our normal use, it is forbidden to disassemble the hydraulic pump. The hydraulic fluid used in the hydraulic system of the hydraulic baler is very compressible. Under normal circumstances, its influence is negligible, so even if the hydraulic baler system contains a small amount of air, the impact on the hydraulic baler is very large. of. The air dissolved in the oil will escape from the oil when the pressure is low, resulting in gas saturation and cavitation. In the high pressure zone, these bubbles are quickly crushed under the action of pressure oil, which is compressed abruptly, causing noise in the hydraulic baler system. At the same time, when the gas is suddenly compressed, a large amount of heat is released, causing local overheating and hydraulic pressure. The components and hydraulic oil are damaged. The high compressibility of the air also causes the actuator to creep, disrupt the smoothness of the work, and sometimes even cause vibration, which affects the normal operation of the hydraulic baler system. According to the different reasons why the air enters the hydraulic baler system, the following points should be noted in the use and maintenance. First, an exhaust valve should be installed on the upper part of the hydraulic baler to facilitate the discharge of the air in the cylinder and the system. The hydraulic baler adapts to changes in oil temperature and load that are greater than the use of a throttle valve. The parallel hydraulic cylinder synchronous circuit of the control valve using the flow rate has a simple structure and a low cost, so the application is relatively common.

    2. Try to prevent any pressure in the hydraulic baler system from being lower than atmospheric pressure. At the same time, use a particularly good sealing device. Replace the failure in time. Screw the pipe joint and each joint surface to clean the hydraulic pressure. The oil filter at the inlet of the baler tank.

    Third, in daily work, always check the height of the liquid oil surface in the hydraulic baler tank, and its height should be maintained on the oil mark scale line. At the lowest surface, the suction nozzle and the same oil pipe mouth should also be kept below the liquid level and must be separated by a partition. If there is an accident, please stop working immediately.as more information ,please visit us : www.nkbaler.com  

    2019-10-08
    Share:
  • It is mainly used for large-scale renewable resource recycling stations, paper mills, etc. for the compression forming of waste paper boxes, newspapers, pit paper and other waste materials. The waste paper packaged with waste paper baler has uniform size, large specific gravity, high density and reduced volume. Such advantages have greatly reduced the space occupied by waste paper and reduced storage costs and transportation costs. Waste carton packaging Waste carton baler is mainly composed of feeding belt, retracting belt, joint connection cutting device, transmission system, track frame and control device. It is divided into semi-automatic, fully automatic, pressurized and other series. The waste carton baler produced by the company has obtained many technical certifications at home and abroad. Introduction of straw baler straw baler: Straw baler is a kind of hydraulic principle, which will loose loose straw, pasture, dry corn straw, straw , wheat straw, all kinds of straw crushing and compression molding, high-density automatic packaging equipment without secondary processing, suitable for working on farms and pasture conditions. The straw and the like are compressed into pieces by compression.

    2019-09-29
    Share:
  • With the increasing emphasis on environmental protection industry in China, the development of straw recovery industry will be gradually improved. On this basis, the level of mechanization of progress seems inevitable. As an important part of the packaging machinery industry, straw balers will in the future be diversified into mechanical functions, structural design standardization, modularization, intelligent control, and high-precision structure. The presentation of the straw baler, a mechanical device, is of great significance to China's packaging machinery industry, and the space for the development of this industry in China has been further explored. At the same time, consumers are satisfied with the increasing requirements for product packaging. Taking industry as an example, the use of the baler is indispensable, and its presentation is satisfied with the messy packaging requirements of the product. In addition, the use of this mechanical equipment is high efficiency, high quality, high environmental protection, and various types of low-cost requirements can be completed. In the future, the development of the baler function will be further broken and accustomed to the needs of the future.as more information ,please visit : www.nickbaler.com  
    2019-09-29
    Share:
  • Many customers are aware of the straw granules and different sizes of granules when consulting the machine. In fact, the straw granule machine and the straw briquetting machine should belong to the straw granule machine. Why are they divided into two models? Of course, because the size of the particles is different, of course, the mold used is not the same. Let's talk about the different parts of the straw pellet machine and the straw briquetting machine.
    Straw granule machine, the mold cylinder type is generally five to six rows of small holes, and the size is from 350 to 580. There are various models, mainly pressing small cylindrical particles, which are generally used in daily biomass boilers, or Biomass burning appliances, because of the small size of the particles, can be formed whether it is straw or wood chips, of course, this also combines the specific material and mold compression ratio. The straw briquetting machine uses a block mold, generally consisting of 36 or 48 blocks, and can produce block biomass particles of different sizes such as 20*20, 30*30, etc., generally used for straw pressing, and can also be pressed. Wood chips, but according to the different raw materials, the mold length, material moisture, composition, reasonable allocation, this block particles, because of the larger, better flame resistance, biomass power plants use more.
    It can be understood from the above that the straw briquetting machine is different from the pellet machine. When the straw briquetting machine is used, the straw is mainly subjected to briquetting treatment, and the pellet machine is mainly made of straw into pellets. According to the needs of customers, using different products, the effect of production can make you more satisfied.
    2019-09-18
    Share:
  • The concentration of China's baler occupation is not enough, and the production capacity is scattered, which cannot constitute a planned economy. At present, the capacity planning of vertical straw balers, horizontal hydraulic balers, silage balers, and green storage balers is faster, but the professional and technological progress is relatively slow, the development and innovation can be low, and the use of vertical straw balers Life and reliability have gradually adapted to the needs of technology development, and technological innovation is urgently needed. Vertical straw balers are still stuck in capacity expansion, which makes China's baler occupation lack a certain brand effect. Therefore, in the technical innovation of vertical straw balers, we must increase our efforts to make contributions to the bale profession in China. The main factors affecting the productivity of vertical straw baler equipment, the most direct impact factors of the production efficiency of vertical straw baler equipment: the model standard of waste paper packaging, the different output values of different models, the standard is not the same, directly determines the production of balers. efficacy. The productivity of the conventional straw baler is higher than that of the bale with the door. The efficient production of the vertical straw baler is also inseparable from the function of the cylinder of the baler. The function of the cylinder determines the stability of the baler. To ensure the efficient production function of the baler, it is necessary to select the manufacturer of the baler with exquisite cylinder manufacturing technology. The quality of the hydraulic oil selected by the vertical straw baler, the quality of the hydraulic oil directly determines whether the cylinder can exert the maximum effect, and directly affects the failure rate and service life of the cylinder. To ensure the efficient production of the baler, you must use the quality and authentic No. 46 anti-wear hydraulic oil. The convenience, control function and low failure rate of the vertical baler equipment control system also determine the packaged running performance. In today's modern society, most straw baler manufacturers are reluctant to develop new products themselves, just thinking of imitating other people's straw baler equipment models.
    2019-09-15
    Share:
Shaanxi Nick Machinery Equipment Co.,LTD 
TEL:86-29-86031588
Fax:86-29-86031588 Sitemap
Add:East Qunsheng Road Wuxi City,Jiangsu,China
Email:info@nkbaler.com  Nickbaler888@gmail.com
WhatsApp:008615021631102 
Copyright © 2018 NKBALER .rights reserved sitemap.html
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top