The bagging machine is mainly suitable for the compression of corn cobs,straws,wood chips,rice husks,cottonseed husks,peanut husks and other scraps.The bags are directly bagged after compression,which is convenient for storage and reduces production costs.

The bagging machine is a fully automatic high-efficiency hydraulic baler newly developed by Nick Machinery,with a high degree of automation.This equipment has low failure rate,high pressure,stable operation and simple operation.The structure is reasonable,firm,easy to use and maintain,which greatly improves productivity and reduces energy consumption and costs.

The equipment of other manufacturers can also work normally under the low moisture content state where the equipment of other manufacturers cannot be pressed normally,and it is very suitable for use with the automatic feeding system.It can also be designed and manufactured according to the compressed size required by the customer.
Welcome friends from all over the world to come to consult and purchase.Company website:www.nkbaler.net,Tel:86-29-86031588

2020-11-16

The rice husk briquetting machine is used to compress wheat husk,rice husk,rice husk,chaff,sawdust,hay,waste edible fungus bag,and all compressed fuel that can be compressed into bags to meet the requirements of reducing freight and saving space.
Now the high-speed limit is limited in height and width,and overloading cannot be used on the road.The best way is to use a rice husk briquetting machine to compress and pack the loose material rice husk,which can reduce the freight.
Operation process of rice husk briquetting machine
 1.The rice husk is fed to the compression box of the equipment through the hopper,belt conveyor,and screw conveyor.
 2.It is squeezed horizontally by the horizontal cylinder of the equipment.

 3.After the second longitudinal extrusion of the longitudinal oil cylinder of the equipment,the cuboid is packed.

 4.Then push the compressed rice husk block into the bag by pushing the bag cylinder.
The recycling value of rice husk is very high.The rice husk from the rice factory is too small for long-distance transportation,which greatly limits the output and benefits of the rice factory.
After years of testing and improvement,Nick Machinery has developed a rice husk baler,which can not only compress rice husks easily,but also process soft materials such as wood chips and coconut chaff,which has won unanimous praise from customers.please visit our website:www.nkbaler.net,or call: 86-29-86031588

2020-11-16

Crushing is one of the important steps in the green storage of feed straw.The crushed straw feed needs to be dried.If the humidity of the straw fragments is too high, it will cause blockage of the packaging equipment.If it is over-dried,it will be difficult to form. This will make the straw baler hydraulic and mechanical wear more serious and it is easy to loose bales after forming.Therefore,choose the drying method according to the production situation in different regions:

1.The natural drying method.After crushing the straw feed,spread it in a sunny place and use the sunlight to evaporate the water.This method is more suitable for manufacturers with premises and lower cost control,but for raw materials Moisture is not easy to control and is easily restricted by weather.

2.The manual drying method can be adopted,and the straw feed can be dried manually. In this case,a dryer is used.The dryer can adjust the moisture content of the straw,which has the advantage that the time for drying is short and the effect is good.
Therefore,when the straw baler is used for production and processing,the above two drying methods can be used to dry the raw materials.
The straw baler produced by Nick Machinery has simple structure,stable action,simple operation,low failure rate and easy cleaning and maintenance.It is a good helper for your production.

2020-11-13

The oil pump failure of the waste paper baler mainly includes oil pump failure,oil suction pipe failure,etc.If the oil pump of the horizontal waste paper baler does not discharge oil,you can check and troubleshoot the fault according to the following methods.
1.If the rotation direction is wrong,stop immediately and correct the rotation direction of the motor.If it continues,it is likely to burn or damage the oil pump.
2.The oil pump of the waste paper packing machine does not rotate.Repair the following couplings.
3.The filter of the fuel tank is clogged,and the suction pipe should be checked.

4.If the viscosity of the anti-wear hydraulic oil of the waste paper baler is too high,pay attention to changing the oil type and install a heater.

5.The suction pipe of the oil pump is not well-sealed.If there is gas,check the suction pipe.
6.The fuel tank filter capacity is insufficient and replace with a larger capacity,pay attention to more than 2 times the pump capacity
The Nick brand waste paper baler is easy to operate and automatically discharges the bale,which improves work efficiency.The installation of emergency stop settings makes the operation safer.
For more information about hydraulic waste paper baler,contact 86-029-86031588 or visit:www.nkbaler.net

2020-11-13

Hydraulic straw balers are classified from the transmission mode.The current waste paper balers,straw balers,plastic bottle balers and other equipment all adopt this method. Therefore,when we hear of hydraulic straw balers,It refers to the waste paper baler equipment currently using hydraulic systems.

The straw baler has two processes to process the straw.After the straw is fed into the straw baler,it undergoes two-stage compression inside the machine to realize the straw baling process.

In the first stage,the straw is relatively loose and requires a small amount of pressure to achieve a larger proportion of deformation.This compression process of the straw baler is mainly to reduce the gap between the straws.Since the straws are relatively loose,the compressed volume at this stage is relatively large.easy to accomplish.

The second stage is mainly compaction.After the first stage of compression,the density between the straws is reduced,and greater compression requires more pressure to achieve.The deformation amplitude of the straw becomes smaller,but the pressure needs to increase faster.The pressure of the straw baler at this stage is mainly to overcome the gaps between the straws.During the compression and packaging process at this stage,it will be affected by the moisture content,feed volume and loading speed.

While developing the performance of the Nick Machinery automatic straw hydraulic baler,it must also reduce the price of the automatic straw hydraulic baler,so that customers are truly aware of the automatic straw hydraulic baler when using the automatic straw baler.Convenient and affordable.
For more information about hydraulic straw baler,contact 86-029-86031588 or visit: www.nkbaler.net

2020-11-12