If metal cutting chips cannot be handled properly, it will cause the following hazards:
1. The cutting oil consumption is large, and a large part of it is taken away by the metal cutting chips, which leads to waste
2. The cutting oil attached to the metal chips will drip and leak during storage and transportation, resulting in dirty, slippery ground (safety hazards) and environmental pollution
3. The content of cutting oil on metal chips will affect the quality and price of metal recycling

4. Since the reform and opening up, my country has vigorously developed heavy industry. A large amount of heavy metal ions are discharged into soil, lakes, rivers and other water bodies, and then into the ocean, seriously endangering human health and living environment.

After years of technical improvement of Nick Machinery, the baler produced by our company has absolute advantages in quality and efficiency at home and abroad. www.nickbaler.net

2023-09-19

With the increasing number of waste materials and the development of hydraulic technology, metal balers, metal shears, and metal chip briquetting machines are increasingly used in various material recycling processing points. Therefore, it is very important to ensure the normal operation of the hydraulic equipment system and increase the reliability of the work. The correct selection of the type and viscosity of the hydraulic oil is the first condition to ensure the long-term and reliable operation of the system.

On the other hand, when the hydraulic equipment system fails, it is also very important to be able to quickly find the cause and effectively solve it. The hydraulic equipment is composed of mechanical, hydraulic, electrical and instrumentation devices. Therefore, when analyzing the failure of the hydraulic equipment system, it is necessary to understand the transmission principle, structural characteristics, components and material configuration of the entire hydraulic system. Since the hydraulic equipment system is a sealed and pressurized system, the flow of oil in the pipeline, the movement of the internal parts of the hydraulic component and the damage of the seal are not easy to observe, so it is difficult to analyze the cause of the failure and judge the location of the failure. There are many reasons for the failure of hydraulic equipment systems such as metal balers, metal shears, and metal chip briquetting machines. Most of the reasons are: mechanical failure of the equipment---such as the unreasonable design of the hydraulic equipment system and the incorrect installation clearance. The quality problems of hydraulic components, improper selection of seals, and operating errors cause hydraulic system failures. This means that the hydraulic equipment system is caused by improper operation by the operator during normal operation, such as the wrong operation sequence or the wrong opening and closing of the valve, and normal operation When the power supply is suddenly interrupted, the temperature or pressure of the hydraulic oil is too high during work, no action is taken, the wrong oil is added when refueling, and the existing oil volume of the oil tank is too much or too little. In addition, the quality of the hydraulic oil causes the failure of the hydraulic equipment system. This is mostly caused by improper oil selection or the use of unqualified oil. It may also be caused by the hydraulic oil being used for a long time, and the new oil is not replaced in time.

The quality of each company's products is the life of the company, and Nick Machinery is no exception. The development of the company always puts quality and reputation in the first place. www.nkbaler.net

2023-09-18

Put the steel scrap to be packed into the bin, operate the reversing valve handle, close the door cover and lock the door cover by the lock to prevent it from floating, and perform primary pre-compression at the same time, and then the side pressure cylinder moves forward to perform secondary compression; When it is in place, the main pressure cylinder moves forward for final compression. After the main pressure cylinder reaches the system pressure, the pressure is maintained for 3-5s. The main and side pressure cylinders return, pull out the lock and open the door cover. On the return journey, a work cycle is completed at this time.
The size of the bale is determined by the weight, material and geometric shape of the added scrap steel. Therefore, it is not allowed to pack too much for the thicker, that is, the denser scrap steel. The block is too long or too large to be turned out of the package block, and even causes the side pressure slider to fail to be in place, causing a series of failures such as the dislocation of the main pressure slider.

Add scrap steel to the bin-operate the reversing valve handle-lock the door cover-at the same time, primary pre-compression-side pressure cylinder working, secondary compression-main pressure cylinder working for final compression-main pressure cylinder holding pressure 5s-side pressure cylinder return stroke-main pressure cylinder return stroke-open the door cover-turn the package cylinder work to turn out the package block and return.

Nick Machinery has strong technical force, creating better value and better service for consumers. www.nickbaler.net

2023-09-15

The metal briquetting machine has a great help in the treatment of scrap steel, which provides a great help in the treatment of scrap steel, so the following is an introduction to the treatment of scrap steel by the equipment.
The main purpose is to process some scrap steel to make it more valuable than before. After being processed by the briquetting machine, you can find that its material shape is more neat, there are few attachments on the scrap steel, and its purity is higher than before. After the briquetting machine is processed, you can find that the scrap briquetting machine has a great effect on the treatment of scrap steel, and its working principle is relatively simple. The scrap briquetting machine is cleaned daily during use to ensure the use of its value and to increase its value.
The briquetting machine is also known as the high-density compacting machine. It is a hydraulic high-density hydraulic high-density of small-size and granular materials such as metal crushing materials, metal crushing materials, metal powder, metal particles, scrap metal, aluminum scrap, steel scrap, iron scrap, copper scrap, etc. The post-forming equipment for the formed scrap metal and the finished briquette recovery furnace can directly reduce the burning loss, increase the ratio, reduce the investment ratio, and directly bring benefits to customers.

In the pressing process, try to suppress metal scraps of the same material. If you need to replace the hydraulic briquetting machine of raw materials, you need to adjust the pressure; during the operation, the operator must carefully observe the metal briquetting machine equipment, if there is abnormality, oil leakage Otherwise, it should stop production for maintenance immediately.

Nick Machinery continues to improve the mechanism, strengthen brand awareness, make the product quality better, better after-sales service, and serve customers in many ways, making Nick Machinery Baler a well-known brand at home and abroad. www.nickbaler.net

2023-09-14

As a new type of straw coal fuel production equipment, what are the factors that affect the combustion performance of the finished product processed by the straw briquetting machine?
First of all: the combustibility of the finished straw briquetting machine is limited by the material properties of the original raw material of the straw coal, and is related to the surface smoothness of the processed finished product. We can see all kinds of surfaces on the market, there are very smooth, good looking, the original opening, looks like a cracked hand, not good looking, different It looks good, but its combustion performance is indeed different. Looking at the straw coal with a very smooth surface, when it burns, due to its poor air permeability, the fuel value cannot be fully released, and the combustion is incomplete, which is also a loss of energy; while looking at the straw briquettes with cracks on the surface When the machine is burned, the cracks can play a role of ventilation, so that the air can completely contact the straw and coal, the oxygen supply is sufficient, the fuel can be completely burned, and all the capacity is released.

Second: density. The higher the density of the finished product processed by the straw briquetting machine, the better the combustion performance of the straw coal and the longer the burning time. However, the higher the density, the better. The appropriate size is better.

The straw baler produced by Nick Machinery has excellent workmanship and strong technology, and is an excellent choice for your baler equipment manufacturer. www.nickbaler.net

2023-09-13