What problems should be paid attention to before using the wheat baler? Next, let’s explore with Nick Machinery!
1. Before use, the wheat straw baler must be adjusted as necessary to check whether the operation of each part is normal. If there is any abnormality, it should be shut down for maintenance;
2. After the hydraulic pipe of the strapping machine is connected to the hydraulic output end, check whether there is any leakage in the hydraulic pipe;
3. The wheat straw baler must be operated in accordance with the operating instructions during use to avoid problems:

4. When the baler is in operation, it is necessary to turn off the engine and cut off the power before clearing it. When the baler is pushed out, it is forbidden to stand in front of the machine to avoid bumps.

Nick machine wheat baling machine has reasonable planning, small footprint, in line with the concept of environmental protection, is your ideal choice. https://www.nkbaler.net

2021-11-01

Wheat balers are mainly suitable for crops such as wheat, pasture, grains, corn, etc. Corn stalk balers and wheat stalk balers are ideal machines to prevent straw burning, increase efficiency, and protect the environment. So what should you pay attention to when using the wheat straw baler, let's take a look with Nick Machinery below:
1. Check the contents marked on the nameplate, including: machine tool model, dimensions, working width, supporting power, production date, name of the manufacturer, etc., and choose a baler that matches your own existing power according to the supporting power of the machine.
2. Choose a manufacturer or seller with a large scale and good after-sales service, which is good for future mechanical maintenance and repair.

3. After selecting the model, check the appearance quality of the machine and whether the exposed rotating parts and the power output shaft are safety protected, and whether they are marked with warning signs.

4. Check whether the machine has the "Three Guarantees" certificate, factory certificate, and instruction manual.
Nick Machinery needs to remind everyone that when choosing, you must choose a regular and qualified manufacturer to better guarantee the quality of the equipment. https://www.nkbaler.net

2021-11-01

There are various kinds of scrap metal resources in daily life, and the sizes are uneven, and it is very troublesome to deal with. If you discard and pile up messy land and pollute the environment, the cost of direct transportation is huge. The emergence of metal shears solves this problem. The problem is that the metal shearing machine can simply cut and process large-sized scrap metal, which is not only convenient for storage, but also for recycling and recycling, which greatly saves transportation costs.
The metal shearing machine has a large shearing force, a wide range of cutting sizes and a wide range of practical applications, and can continue cutting. When it is cut by a high degree of scrap steel, its oil pump can actively reduce the flow, and its motor will not exceed It burns out under load, so the metal shearing machine is the best choice for metal material recycling departments to cut waste.
The metal shearing machine is suitable for cold shearing of metals with various cross-sectional shapes and various scrap metal structural parts, making scrap metal easy to pack, store, and transport, and provide qualified charge for smelting in smelters.

The metal shearing machine has a wide range of applications. It can be used as processing equipment for metal recycling and processing units, as well as for furnace material processing in factory foundries and metal cutting processing equipment in the mechanical construction industry.

NICKBALER metal shearing machine has the characteristics of fast speed, simple structure, stable action, low failure rate and easy cleaning and maintenance. https://www.nkbaler.net

2021-10-29

The safe operation of hydraulic tiger head shears is not only related to the personal safety of the operator, but also affects the quality and performance of the equipment. The manufacturer will train the operator on how to operate and maintain the equipment in order to allow the equipment to work normally for a long time.
What are the precautions for hydraulic tiger head shears?
1. The human body is not allowed to approach the transmission part and the knife edge of the equipment during operation. Pay attention to the safety of the surrounding personnel to prevent the material from lifting and hurting people. When cutting, cut as close as possible to the inside of the knife edge;
2. When the tiger head shearing machine has serious oil leakage or abnormal phenomenon, it should stop immediately, analyze the cause, eliminate the fault, and do not force the operation with the fault;
3. When adjusting the pump, valve and pressure gauge, the tiger head shearing machine must be operated by experienced technicians. If the pressure gauge is found to be faulty, it should be shut down immediately for inspection or maintenance;
4. When the equipment is running, the operator shall not leave the post without authorization. When the work is over or temporarily leave the working position, the power supply shall be cut off;

5. The hydraulic oil should be cleaned and replaced every six months, but the first cleaning and filtering of the oil should not exceed one month. The new oil used once is strictly filtered and allowed to be reused.

The NICKBALER Tiger Head Shearing Machine has reliable performance, convenient operation and simple maintenance. Diesel engines can be used as power where there is no power supply. https://www.nkbaler.net

2021-10-29

Regardless of the performance of the horizontal baler, it can be summarized as the strength of the horizontal baler's execution ability. The work must ensure the stability of the operation to ensure the uniformity of the packages.
So what causes the horizontal baler to not work quickly?
1. The oil supply pressure of the horizontal Baler oil pump cannot meet the flow demand. In order to prevent the occurrence of oil leakage, strict inspection and testing must be carried out before work.
2. If the overflow valve in the horizontal baler is deformed, it will seriously affect the main valve core blockage. The main valve core is blocked in the small opening, which will easily cause some pressure oil output by the baler oil pump to overflow into the tank, causing the baler The flow of CNPC into the actuator is greatly reduced, which slows down the rate of oil supply.
3. The internal and external oil leakage is relatively serious. In fast work, it is easy to cause the oil supply pressure to be too low, but the pressure is much higher than the oil return line. When the piston seal of the Baler machine cylinder is damaged, the two sides of the Baler machine cylinder are easy The accident that caused excessive internal leakage resulted in insufficient rapid movement speed of the cylinder of the horizontal baler, and oil leakage was likely to occur in other parts.

4. A series of reasons such as the lubrication of the guide rail and the poor installation accuracy and assembly accuracy of the oil cylinder in the horizontal baler can easily cause the friction resistance to increase when the baler is working.

The baler produced by NICKBALER has the characteristics of many varieties, complete specifications, strong matching, etc., and can be designed and manufactured according to customer requirements. https://www.nkbaler.net

2021-10-29