A metal baler is a common piece of industrial equipment used to bale various metal scrap or other materials into compact chunks for transport and processing. When using a metal baler, you may encounter a situation where it cannot be started. There are several reasons for this situation:
1. Not connected to the power supply: If the metal baler is not connected to the power supply or the power cord is not in good contact, it will fail to start.
2. Hydraulic system failure: The hydraulic system is the core component of the metal baler. If the hydraulic oil temperature is too high, the oil pump is damaged or the oil pipe leaks, the whole machine will not start.

3. Control system failure: such as control panel failure, sensor failure and other problems will also affect the start and operation of the metal baler.

Nick Machinery has accumulated rich experience since its establishment, and its strength has also been greatly improved. 

2023-12-06

In industrial production, a metal baler is a commonly used device for compressing and packaging metal scrap, paper, plastic and other materials for easy transportation and processing. The hydraulic system is one of the core components of the metal baler, which realizes Machinery operation through the transmission of hydraulic oil. However, how much hydraulic oil should be added to a metal baler?
1. We need to understand the role of hydraulic oil in metal balers. Hydraulic oil is not only used to transmit power, but also plays important roles such as lubrication, sealing and cooling.
2. To determine the amount of hydraulic oil required for the metal baler, first check the operation manual of the equipment or the technical specifications provided by the manufacturer.
3. It can reduce friction loss, maintain the normal working temperature of the hydraulic system, and prevent leakage and oxidation at the same time.
4. Generally speaking, the amount of hydraulic oil used will be stated in the technical specifications provided by the equipment manufacturer.

5. How much hydraulic oil to add to the metal baler mainly depends on the design of the equipment and the manufacturer's suggestion. Consulting your equipment manual for the correct type and amount of hydraulic fluid to use is critical.

The metal baler adopts hydraulic drive, which is easy to operate and easy to maintain. There is no need for foot screws for installation, and diesel engines can be used as power in places without power supply. The equipment adopts hydraulic transmission, which is safe to use and easy to realize overload protection. 

2023-12-05

The hydraulic baler is used to squeeze waste paper and similar products firmly under normal conditions.
1. String the Baling Press rope of the hydraulic baler through the automatic elastic device behind the garbage compressor.
2. Put the recycled waste paper, plastic, and film waste into the hydraulic baler, close the door tightly, and press the "press down" button. The equipment runs automatically and compacts.
3. Return to the fully open position. When compressing Baling Press constraints, the platen stops at the preset position of the compressed material.
4. Push the pull rod to a fixed position and lock it tightly. Press the "up" button, and the return stroke of the oil cylinder will automatically pull out the bundled bundles.

5. After the bales of the hydraulic baler pop up, reset the baling rod to press down. Close the door and lock it tightly to enter the next packaging cycle task.

Nick Baler has a professional R&D design and after-sales team. If you encounter any difficult problems during use, you can always go to the Nick Baler website for consultation: https://www.nkbaler.com

2023-12-04

The gear on the hydraulic metal chip briquetting machine plays a very important role in the work of the equipment and cannot be bent. If it is found to vibrate when it is running at a slow speed when starting up, there are generally three reasons:
1. The four pillars are too tight. Treatment method: You must add some hydraulic oil to the four columns in the hydraulic metal chip briquetting machine.
2. The pressure of the support valve in the lower chamber of the master cylinder is unstable or the support force is too low. Solution: The support valve in the lower chamber of the master cylinder is unstable. The pressure of the support valve can be appropriately increased or decreased, or the spring can be replaced.

3. There is a problem with the pilot solenoid valve of the support valve in the metal chip briquetting machine equipment. Treatment method: Whether the spool of the solenoid valve is flexible, whether the matching gap is too large, and deal with the phenomenon of leakage.

Choosing Nick Machinery hydraulic baler, independent hydraulic system, servo system control, is the best choice to help you solve and recycle waste. 

2023-12-01

The servo system hydraulic baler is an advanced packaging equipment that combines the characteristics of the traditional hydraulic baler and has many advantages.
Nick Baler is one of the excellent brands of servo system hydraulic balers.

Nick Baler servo system hydraulic balers offer greater accuracy and stability than traditional hydraulic balers. It uses advanced servo motor control technology to achieve precise compression force control, ensuring that each packaging bag can achieve the ideal compression effect. In addition, Nick Baler also uses advanced sensor technology to monitor various parameters during the packaging process in real time, such as pressure, temperature, etc., thereby ensuring the stability of the entire packaging process.

In addition to high precision and stability, Nick Baler servo hydraulic balers are also fast. It adopts advanced hydraulic transmission technology to achieve rapid compression action, thereby improving packaging efficiency. In addition, Nick Baler also adopts an advanced automated control system that can realize automatic feeding, automatic compression, automatic sealing and other functions, thus further improving packaging efficiency.
In short, the Nick Baler servo system hydraulic baler is an advanced packaging equipment that combines the characteristics of traditional hydraulic balers and has the advantages of high precision, high stability, and rapidity. It can meet the needs of various industries for packaging equipment and provides strong support for enterprises to improve production efficiency and reduce costs. If you are looking for a great servo hydraulic baler, then the Nick Baler is definitely worth your consideration!

2023-11-30