The waste paper hydraulic baler works frequently. If the maintenance is not in place, the wear and tear of the components will inevitably occur. In order to make the equipment work in an excellent state, maintain
Care work needs to be done in a timely manner.
1.Check it regularly once a week to clean up the dirt and grease inside the baler.
2.Check each part regularly every month, and maintain and lubricate the upper sliding plate, middle knife and front top knife of the equipment.
3.Carry out major maintenance on the waste paper baler every quarter, and add lubricating oil to each actuator to keep the equipment in a good lubricating state.

4.Replenish the oil in the reducer wheel box every year.

NICKBALER warmly reminds you: When using the baler, you should strictly follow the operating instructions. If you want to know more about after-sales maintenance, please contact us at 86-29-86031588

2022-10-27

At present, various environmental pollution, air pollution, water pollution, garbage pollution and many other problems have always existed in our lives, and some even have a serious impact on our lives. Therefore, the whole people advocate green and pollution-free, green life is what we all pursue, and we look forward to a green living environment.

For waste plastic pollution, one of the pollutions, the waste plastic baler has really made a great contribution. The existence of waste plastic balers plays a vital role in the recycling and reuse of waste plastic balers. The waste plastic baler is mainly used to pack some waste plastic balers, leftover materials, corrugated paper, waste plastic packaging boxes, waste newspapers and other items. The packaged waste plastic balers occupy a small area, saving inventory costs and manpower. resources, and greatly improve the utilization rate of waste plastic balers, and greatly improve the surrounding environment of the enterprise.

NICKBALER is a manufacturer specializing in the production of balers. We are committed to the development of environmentally friendly waste plastic balers and hope to contribute to our environmental protection through our own efforts. For more information, please consult https://www.nickbaler.net

2022-10-25

1. A wide range of feed raw materials, various green feed, green crop straw, melon, vine and vegetable seedlings, high-moisture grains, slag, etc., can be used to make straw balers;
2. High nutritional value; more than 85% of the nutrients in the forage can be preserved, while the prepared hay can only retain 80% of the nutrients even under the best conditions; under poor conditions, only 50-60% can be retained nutrients;
3. High nutrient yield per unit area. Planting feed crops on the same area of land to prepare straw balers has 30-50% higher nutrient yield than harvesting fruit;
4. Not affected by seasons and weather;
5. The production process is simple and requires less labor;
6. Compared with saving hay, making a straw baler occupies a small area;

7. The straw baler has a sour fragrance after microbial anaerobic fermentation, good palatability and high feed intake

Follow NICKBALER, you can learn more skills and tips https://www.nickbaler.net

2022-10-24

The metal powder cake press needs to work every day. In some large factories, it will not be idle even at night. In order to make the metal powder cake press run safely every day, it is necessary to do daily inspections. The cause of the failure can be found and determined. So, how to do the daily inspection of the metal powder cake press .I summarize it for you in three steps:
1. Check whether the screws at the pressure regulators of the flow valve and other pressure valves are loose. If the pressure regulating screw of the relief valve is loose, the working pressure of the system will not reach the predetermined value or the working pressure cannot be established, and the system will not work normally. The loosening of the adjusting screw of the pressure reducing valve will make the outlet pressure less than the predetermined value, so that the pressure reducing circuit cannot work normally.
2. The amount and temperature of oil in the tank. The amount of oil in the fuel tank should always be kept within the normal range, otherwise it should be replenished in time. The grade of the added oil must be the same as that of the system, and it must be tested to meet the specified indicators; the added oil should be filtered, and the filtration accuracy Not less than the accuracy requirements of the system 

3. Oil leakage at various sealing parts and pipe joints. It is inevitable and common for hydraulic systems to leak under working conditions. Leakage leads to a decrease in system pressure, resulting in unstable speed of actuators, wasting oil, consuming energy, reducing efficiency, increasing oil temperature, polluting the environment, and causing fire hazards. The leakage of the system mostly occurs at the fixed seal and the moving seal. The cause of leakage is usually the damage, aging, damage of the seal or the vibration of the loose connecting screw, which should be repaired in time. Leaks under non-working conditions are not allowed.

NICKBALER Machinery warmly reminds you: When using the baler, you should strictly follow the operating instructions. If you want to know more about after-sales maintenance, please contact us at 86-29-86031588

2022-10-21

We all know that the area of waste paper balers varies greatly depending on the model. For example, the common horizontal baler covers an area of 10-200 square meters depending on the model. How can the baler be installed in a small room?
If you want to install it in a small room, we do not recommend installing a horizontal model. You can choose a vertical waste paper baler, which is characterized by a vertical all-in-one machine, a front door type, and a small footprint. It is an ideal model for volume reduction and recycling.
It should be noted that the foundation ground of the hydraulic waste paper baler must be flat, tamped and hard, and its metal substrate must be flat without any deformation. When the ground is soft, a sweeping rod or a backing plate must be used to increase the force surface and stability.

Therefore, if there are friends in need, you can explain the use requirements and site area, and we will recommend the appropriate type of waste paper baler according to the actual situation. If you have other questions, please contact our factory.

For more detailed description of waste paper baler, you can go to NICKBALER Machinery's website: https://www.nickbaler.net, or you can call our sales phone: 86-29-86031588.

2022-10-20