WhatsApp:008615021631102      Email:sales@nkbaler.com       TEL:86-29-86031588
News Center
You Position : Home >> News Center
  • In the use of the waste paper baler, moisture should be prevented from entering, so as not to affect the normal use of the waste paper baler and cause the performance of the machine to decrease. The moisture mentioned here refers to the influence of the surrounding cooling water, water vapor or moisture. However, the various waste paper balers  appearing on the market now make many users feel dazzled. People don’t know how to choose a waste paper baler that suits them.  In fact, people have not yet understood the waste paper baler. , As long as we have an understanding of his types and functions, it is not difficult to choose a suitable Baling Press.

    At the same time, we have selected a Baling Press that suits you, and you must maintain it properly during use, otherwise the Baling Press will also bring us some minor troubles. Pay attention to the anti-freezing work of the motor and the long-term overload of the motor. Effective prevention of these two can greatly reduce the damage of the motor, thereby maintaining the normal packaging of the waste paper baler. Another thing is to pay attention to the button operation of the console part, do not use excessive force on the switch button, and prevent misoperation to avoid short circuit damage. 

    In the process of a working cycle, the empty stroke speed of the waste paper baler is generally high, and it has different movements and bears different loads in different working stages. Therefore, in the hydraulic system, the flow rate and pressure of the hydraulic pump are often determined according to the required movement speed and the load to be received during the working phase. Then, without increasing power consumption, a fast loop is used to increase the idle stroke speed of the working mechanism. The characteristic of the fast circuit is that the load is small (the pressure is small) and the flow is large. Double hydraulic pumps are now used for oil supply. The low-pressure pedestrian flow pump and the high-pressure low-flow pump are connected in parallel. They supply oil to the system at the same time to realize the rapid movement of the hydraulic cylinder. When entering the work advancement stage, the system pressure rises and the solenoid valve opens to unload the pedestrian flow pump. The small flow pump supplies oil to the system, and the movement of the oil cylinder becomes a slow-moving work stroke.
    Nick Machinery has a professional R&D, design and after-sales team. If you encounter any difficult problems during use, you can always contact us www.nkbaler.com.
    2021-04-01
    Share:
  • The hydraulic garment strapping machine has a compact structure and beautiful appearance; hydraulic compaction, manual loading, button control, high pressure, fast speed, and high efficiency; two strapping slots, simple operation; open structure, convenient observation; and can completely maintain clothing , The integrity of the fabric; the height-adjustable seat feet; maintenance-free use, easy to keep the working environment clean; fast compaction, high efficiency; the pressure plate automatically returns.

    Precautions

    When opening the door, people should stand in front of the machine and open the front door first, and then open the front door. When opening the door, people should stand at a 45° position on the front of the machine. People should stay away from the machine as far as possible, because the rebound force of the scissor buckle is very strong when opening the door. BigPay attention to the average, not beyond the packaging room; if it exceeds the surrounding area, it is easy to bend and deform the door, and severely crush the main body.
    Shaanxi Nick Machinery Equipment Co., Ltd. has been committed to the research, development, and production of garment balers and hydraulic balers for many years, and has perfect after-sales service. For details, please visit www.nkbaler.com
    2021-04-01
    Share:
  • This series of balers are divided into horizontal bars and parallel bars. They have the characteristics of sufficient pressure, safety and durability. They are widely used in garment underwear factories, old article recycling companies, 
    old clothes exporters, waste stations and other enterprises. Clothing, down jackets, quilts, shoes, etc. are packaged and recycled. It is a good equipment to improve labor efficiency, reduce labor intensity, save manpower, and reduce 
    costs. The nominal pressure is 30T-50T-60T-80T-120T and other specifications.
    Machine installation steps
    1. The machine must be steadily placed on the ground without swinging.
    2. The pressure of the machine has been fully adjusted before leaving the factory, and it can be used after injecting 68# anti-wear hydraulic oil and connecting it to the power supply
    3. The voltage and frequency of the machine are: 380V/50Hz (the export machine is customized according to the local voltage), three-phase four-wire system, three wires are connected to the corresponding terminal of the electrical box, 
    and one ground wire is connected to the metal of the electrical box to prevent leakage;
    4. Turn on the main power switch, and then press the machine start button to test the machine;
    5. The manual reversing valve has three gears, which are divided into: upper, middle, and lower; middle position: the pressure plate stops; the lower position: the pressure plate is pressed down; the upper position: the pressure plate is 
    raised;
    6. When testing the machine, check the rotation of the motor. There is an arrow mark. If the pressure plate is not pressed down, the power cord should be exchanged.
    7. After the machine is debugged, the pressure plate can go up and down normally; close the door of the machine, operate it several times, exhaust the air in the tubing, and then put the materials into the box for compression and packaging;

    8. After the package is finished, the strapping should be carried out. The pressure plate should be pushed to the bottom, the manual reversing valve should be set to the middle gear, press the switch, the motor will stop, and the machine door should be opened. Remember that people should stand on the side when opening the door. Stand up to prevent people from opening the door to hurt people;
    9. When all the doors are opened, tie them with packing tapes according to the symmetrical grooves on the upper and lower pressure plates. After they are tied, turn on the power supply and raise the pressure plates;
    10. Remove the packaged materials from the machine; lay a package;
    Nick Machinery can tailor the packaging machine according to your packaging requirements, space size, and budget constraints. You can contact us for more information in order to recommend the best packaging solution for you. You are welcome to consult www.nkbaler.com.
    2021-04-01
    Share:
  • Scrap recycling is a hot topic in the society nowadays, including beverage bottles, cans, scrap bicycles and motorcycles, scrap aluminum, scrap home appliances, etc., industrial scrap metal, scrap steel, scrap iron, light and thin materials, etc. It can be recycled, and some cannot be recycled. Take the most common scrap metal among them, it can be recycled resources. So what is the use of scrap metal after it is processed by a metal briquetting machine?

    The metal briquetting machine is a kind of mechanical equipment that can recycle scrap metal resources for briquetting and packaging. Anyone who knows this industry knows that the cost of recycling scrap metal on the market is very low, and the metal briquetting machine is used for briquetting and packaging After that, it will become a cuboid.

    In addition, there are many sales channels for scrap metal after briquetting and packaging, which not only facilitates transportation, but can also be directly sent to steel plants for recycling. Nick Machinery specializes in manufacturing various hydraulic balers to compress and bale waste materials into compact bales that are small in size and easy to handle. We can customize the packing machine that meets your packing needs at a reasonable price according to your needs. If you have any requirements, please contact us www.nkbaler.com. 


    2021-03-31
    Share:
  • The hydraulic straw briquetting machine is classified from the transmission mode. Waste paper briquetting machine, straw briquetting machine, plastic bottle briquetting machine and other equipment are now used in this way. Therefore, when you hear about hydraulic straw briquetting machine, it refers to the straw briquetting machine equipment currently using hydraulic system. There are two methods for straw briquetting machine. After the straw is sent to the baler, the straw is packed into the machine in two compression stages.
    In the first stage, the straw briquettes are relatively loose and require a small amount of pressure to achieve a larger proportion of deformation.

    The relationship between process pressure and deformation can be approximately equal to a linear relationship. The compression process of the straw briquetting machine is mainly to reduce the gap between the briquettes. Since the straw itself is relatively loose, the amount of compression at this stage is relatively large. Easy to complete.

    The next step is mainly compact. After the previous stage of compression, the density between the straw briquettes decreases, and more compression is needed to achieve greater compression. The deformation of the straw becomes smaller, but the pressure needs to increase faster. The relationship between material deformation and pressure is a non-linear relationship. At this stage, the pressure of the straw briquetting machine is mainly to overcome the gaps inside the straw. At this stage, the compressed filler is greatly affected by moisture, feed rate and loading rate.
    The maintenance of hydraulic straw briquetting machine should be kept tidy, clean, firm, lubricated, anti-corrosive and stable. Daily inspection, maintenance and regular inspection of parts: check cylinders, oil pumps, electrical appliances and sliding parts. Maintain and inspect machine parts and modifiers. Check the power cord of the machine and make sure to put the power cord on the forklift and the aisle to avoid stress on the power cord.

    2021-03-31
    Share:
Shaanxi Nick Machinery Equipment Co. LTD 
TEL:86-29-86031588
Fax:86-29-86031588 Sitemap
Add:East Qunsheng Road Wuxi City,Jiangsu,China
Email:nk@nkbaler.com  Nickbaler888@gmail.com
WhatsApp:008615021631102 
Copyright © 2018 NKBALER .rights reserved
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top