The temperature has a great influence on the hydraulic baler. If the temperature of the hydraulic oil is too high, the equipment will be unstable and leak oil; if the temperature is too low, the hydraulic cylinder resistance will be too large, causing the equipment efficiency to be too low. In order to improve the performance and efficiency of the equipment, How much should we control the working oil temperature of the hydraulic baler?
Under normal circumstances, the oil temperature of the hydraulic oil of the hydraulic baler should be between 30-80 degrees. The temperature is too low, the oil viscosity is large, the fluidity is poor, the resistance is large, and the work efficiency is low; if the oil temperature is lower than 20 degrees, the hydraulic motors, valves, pipelines, etc. are easily damaged in sharp turns; if the oil temperature of the hydraulic system of the hydraulic baler is too high , It will reduce the viscosity of the hydraulic oil, easily cause leakage, reduce efficiency, reduce the strength of the lubricating oil, the paint film, accelerate the wear of the machine, produce carbides and sludge, accelerate the deterioration of the oil quality, and cause the oil, oil seal, and high-pressure rubber pipe to pass Early oxidation.
1. When the temperature of the hydraulic oil is too low, we need to preheat the hydraulic system and start the equipment. After the hydraulic baler is idling for 3-5 minutes, it will work under pressure to maximize any movement of the working device and keep it 3 -5 minutes to preheat the hydraulic oil through the overflow;
2. If the oil temperature is too high, you need to appropriately increase the preheating operation time. When the temperature of the Baler exceeds the standard, pay attention to the radiator heat sink not to be contaminated by oil to prevent dust adhesion and affect the heat dissipation effect; the hydraulic Baler should keep enough oil In order to facilitate the circulation and heat dissipation of the oil.

The above is the normal oil temperature of the hydraulic baler that Nick summed up for you. Generally, thermometers are installed on the equipment. Once this range is exceeded, it needs to be overhauled and maintained to avoid damage to the hydraulic baler. For more information, please pay attention to www.nkbaler.net

2021-06-18

The main hydraulic system of hydraulic equipment is mainly composed of an oil tank and an oil pump. The hydraulic oil pump is the power source of the hydraulic system. The hydraulic oil pump we choose should meet the pressure and flow requirements of the oil tank of the hydraulic system. At the same time, we should fully consider the reliability, service life and maintainability, so that the selected hydraulic oil pump can operate in the tank hydraulic system for a long time. This is the subtle relationship between the two in the device:
The hydraulic oil tank in the hydraulic machine equipment is installed with:
1. The inlet cover is installed on the top of the oil tank, and there are two, among which the hydraulic air filter is installed on the inlet cover of the oil tank return area.
2. The hydraulic air filter filters the air circulating in the oil tank, and filters the oil when the oil tank is refueled.
3. Two level gauges, installed on the front side of the fuel tank, with two level gauges, high and low.
4. The oil temperature gauge is installed on the front side of the oil tank to measure the oil temperature in the oil tank. The normal working oil temperature is 30～70℃;
5. Two main oil return ports, set on the bottom plate of the oil tank, equipped with a one-way valve, respectively connected to the main oil return pipe and the overflow valve oil return port; the one-way valve is automatically closed when the hydraulic pipeline is repaired to prevent it from being in the oil tank The oil is lost.
6. The drain port is set on the bottom plate of the fuel tank and is blocked with a plug; the hydraulic oil of the fuel tank can be drained by opening the plug.
7. The suction port of the main oil pump is set on the front side of the oil tank, and the main suction filter is installed;
8. The oil suction port of the steering oil pump is set on the front side of the oil tank, and the steering oil suction filter is installed;
9. The oil return port of the steering system is set on the bottom plate of the oil tank and is equipped with a one-way valve. The one-way valve is automatically closed when the hydraulic pipeline is repaired to prevent oil loss in the oil tank;
The hydraulic oil pump in the equipment: the single gear structure is respectively installed on two hydraulic transmission power take-off boxes, driven by the torque converter pump wheel, the engine rotates, and the power take-off box can drive the oil pump. The power take-off box is equipped with a hydraulic clutch. When hydraulic action is required, you can operate the "hydraulic pump clutch" handle of the driller control box and set it to the "oil pump I on" position, and the oil pump I is combined to output working pressure oil; the handle is set to "oil pump II" "Close" position, the oil pump II is combined to output working pressure oil;. The handle is placed in the middle position, and the two oil pumps are separated and stopped.

Nick Machinery is an enterprise specializing in the production of hydraulic machinery and accessories, allowing you to buy one-stop, worry-free after-sales. Welcome to buy: www.nkbaler.net

2021-06-18

Nick Machinery sells hydraulic balers all year round. Our vertical balers are mainly used to recycle packaging materials and waste products such as compressed cardboard, waste film, waste paper, foam, beverage cans and industrial scraps. This vertical baler can fully reduce waste storage space and save up to 80% of the stacking space, can fully reduce transportation costs, save space, and is conducive to environmental protection and waste recycling.
Nick Machinery’s products have always been quality-oriented, and the subtleties are true. Whether the details can be done well determines the quality level of the vertical baler. Nick's vertical baler product details use high-quality electronic components, pay attention to process integration, and the specific details use pure copper motors. This kind of motor is more powerful, durable, faster and more efficient in heat dissipation, and can ensure the stability of the baler Operation; gear oil pump, high flow rate, high temperature resistance, extremely fast oil supply, high-speed operation without wear, using 8.8 high-strength fastening screws to prevent any trace of oil leakage. Imported electric box is used, which is durable and can be changed at any time. Chrome-plated oil cylinder, the oil cylinder adopts chrome-plating process, does not rust and does not leak oil, the oil cylinder is large in size, fully loaded with more oil, and the firepower does not stop. The welding process, the whole machine is sturdy and durable, does not open the welding, and the welding points are not obvious. The appearance of the whole machine is excellent. The U-shaped anti-release lock is adopted, which is more user-friendly, convenient and durable. In addition, the vertical baler produced by Nick includes different cylinder specifications, including different specifications from 8 tons to 120 tons, which can fully meet the diverse needs of customers.

In order to achieve the weight of the bale required by the customer, you can contact the sales team of Nick Machinery to design and customize the reasonable machine pressure and cavity size according to your material characteristics. 86-29-86031588.

2021-06-17

The vertical can Baling Press has the characteristics of good rigidity, toughness and stability, beautiful appearance, convenient operation and maintenance, stable and energy-saving, and low investment cost of equipment basic engineering. It is widely used in waste recycling companies and enterprises. It is suitable for the packaging and recycling of waste cans, plastic bottles, aluminum cans, etc. It is to improve labor efficiency, reduce labor intensity, save manpower, and reduce vertical cans. Product details:
1. No installation required and simple operation: After the machine is refueled and connected, it does not need to be installed. You can directly operate the control lever to start the compression work. The left lever controls the pressure plate, and the right lever controls the push bag. It is easy and convenient to lift and pull.  
2. U-shaped anti-dropping door handle: The door handle is updated, and the U-shaped design is non-slip and easy to unlock. Greatly reduce the time cost after packaging.  
3. Good copper-core motors: all motors use brand-name copper-core motors, which have strong power, durability and faster heat dissipation, ensuring stable and continuous operation of the machine.  
4. Automatic package pushing and turning package design: automatic pushing and turning package support customized customization, easy to operate, the package can be directly mechanically output after the pressing work is completed, which effectively saves labor.  
5. High-sealing and wear-resistant tubing: Imported abrasion-resistant and high-sealing tubing. The thick wall of the tubing has a strong sealing connection to ensure no oil leakage during compression.  
6. Thickened steel plate: thickened body, stable packaging and long service life.  
7. Gear oil pump: large flow rate, strong self-priming ability, high temperature resistance, fast oil supply.
The vertical can Baling Press is mainly suitable for recycling plastic beverage bottles, cans, PET cola bottles, oil bottles, beverage cans and other packaging materials and waste products. This vertical baler reduces waste storage space, saves up to 80% of stacking space, reduces transportation costs, and is conducive to environmental protection and waste recycling. Become an indispensable equipment for waste recycling stations

The Nick brand can Baling Press is safe, reliable, simple in structure, economical and reasonable, easy to use, and simple in maintenance and operation. It is a good helper for your production.

2021-06-17

In this era when the baler is widely used, we must operate and use the baler reasonably to avoid working failures. Then in the process of using the baler, what issues need to be paid attention to, let’s take a look at the use of the baler for everyone. matter.
1. The most important thing is, of course, personal safety. The baler is a kind of industrial machinery and equipment. In the process of using many large desktop balers, we must pay attention to the use of specifications. After the baler is powered on and enters the working process of baling and bundling, the operator must be careful not to reach into the machine to avoid accidents. The baler is a metal mechanical equipment with a hard texture. The mechanical parts are running fast during the strapping process, and the current technology is unable to distinguish the difference between the human body and the goods. In many cases, it is because the operator does not operate correctly in accordance with the operating specifications. This may cause personal injury. In the same way, after a long period of use, the equipment will inevitably experience aging and damage. At this time, it is necessary for the staff to perform regular repairs and maintenance. It should be noted here that when working, the staff must disconnect the power supply in advance, and then carry out standardized maintenance according to the maintenance rules. The correct use of the baler can not only ensure our personal safety, but also ensure that the work process can be carried out quickly and without obstacles.
2. The baler is an industrial metal strapping machinery and equipment, of course, it also has the characteristics of metal-easy to rust, the cause of rust is metal oxidation. So here is a reminder to everyone. The placement environment of the baler must be dry and not placed in a humid environment to avoid accelerating the rust and aging of the baler equipment. Moreover, the baler is also a kind of electrical equipment. If the environment is excessive Moisture can also easily lead to failures such as electrical connection of the motor. Therefore, for our personal safety and to improve the service life of the baler, do not place and use the baler in a humid environment.
3. The safety of the power supply of the baler is a commonplace issue, and we must treat it with caution. When installing the baler equipment, you must first understand the number of phases of the equipment power supply. If it is a three-phase power supply equipment, make sure that the power cord is grounded during installation to avoid electrostatic failure. Before using the equipment, pay attention to check whether the mechanical equipment can be turned on normally, and remember to cut off the power after use to avoid accidents.
4. Do not operate the baler in a severely dusty environment. This problem is not only the existence of the baler, but almost all electrical equipment will have this requirement. Everyone knows that the dust itself is charged. When the dust deposits around the equipment, it will cause a short circuit of the equipment. When the dust accumulates between the front ends of the equipment switch, it will also cause poor contact of the switch. Remind customers that if the baler equipment appears up and down, the first thing to check is whether the switch has poor contact due to dust accumulation. And if the dust accumulates too much, it will affect the heat dissipation of the equipment's motor, causing the equipment's motor to overheat and reduce the carrying capacity of the equipment.
5. The cleaning and maintenance of the packing machine. For the production enterprise, the packing machine is a kind of mechanical equipment that is used very frequently. During frequent use, attention should be paid to the regular maintenance and cleaning of the equipment to avoid the impact of unsmooth operation. The process of arriving at the factory, so that the gain is not worth the loss. Just like if you raise a horse and you want it to work, you must feed it regularly. The machinery and equipment are the same. If you want the equipment to work normally and smoothly, then regularly The maintenance and cleaning of the equipment is inevitable, and the manufacturers who use the equipment should be warned to put this matter into the process as soon as possible to extend the service life of the equipment and reduce the cost of repairing and replacing the equipment.

Here, Nick Machinery advises you that the standardized and safe use of baler equipment is something that every manufacturer must implement. Only standardized operations can ensure the efficient and rapid production process and create greater value for the enterprise

2021-06-16