5. Special attention should be paid to: non-technical personnel can not disassemble and adjust the places that are not described in the booklet at will, especially the places with red paint on the packaged fuselage.
Gantry shears are ideal machines for cutting stainless steel Nick Baler plates, electrolytic copper plates, ship plates, and materials.
The straw Baler machine is a new type of tool used in agriculture. It uses materials with good wear resistance and impact resistance to ensure the stability of the equipment and make its performance more excellent. The briquette has high density, high calorific value, good combustion, low cost, easy to use, clean and hygienic, and easy to store and transport.
The straw Baler machine compresses the crushed corn stalks, wheat stalks, peanut husks, rice husks, sawdust, wood chips, tree bark, etc. into lumps without any additives and binders. The materials used are: High-quality alloy steel greatly improves the strength of the material on the basis of the willfulness of the material during heat treatment.
The main shaft of the straw Baler machine adopts a hexagonal structure and is connected with the bracket with a taper sleeve. This structure has high reliability, as long as the main shaft is continuous, there will be no failures, and it is convenient to disassemble during maintenance. The main shaft of the Baler machine of other manufacturers adopts the key connection. This structure is prone to failure due to the large transmission power. Even if the installation is tight and does not fail, due to the dust and water vapor generated during work, coupled with the temperature, rust conditions will occur, and the equipment cannot be disassembled during maintenance. Therefore, the structure of the Dongshan straw Baler machine is more reasonable, so as to achieve high conversion of kinetic energy and improve the production efficiency of the equipment.
The straw Baler machine produced by the straw Baler machine can replace traditional coal and be directly applied to the new type of biomass boiler equipment. The briquettes produced by the straw Baler machine are ideal products for livestock farms, rural biomass boilers for heating, and power plants.
The straw Baler machine presses or bales the straw, which facilitates the storage of the straw and also increases the utilization rate of the straw.
The straw Baler machine produced by Nick Machinery has simple structure, high production efficiency and convenient operation. If you are interested in understanding, you can go to our company website for more information www.nkbaler.net.
The straw Baler machine is an environmentally friendly equipment, used to crush the compressed fuel and servo materials of bio-energy raw materials such as straw. The crushed forage can be used as a servo agent or fuel. After practice and improvement, the straw Baler machine is becoming more and more perfect. The machine has high degree of automation, large output, low price, low energy consumption, simple operation and no environmental pollution. Rice stalk Baler machine widely used for crushing various crop stalks, twigs and other raw materials. If there is no electrical equipment, diesel engines can be used instead.
The Baler machine has strong material adaptability: it is suitable for the molding of various biomass energy raw materials. The straw can be processed and molded from powder to 50mm in length.
The automatic adjustment function of the pressing wheel of the Baler machine: the pressure angle is automatically adjusted by the principle of two-way rotation of the thrust bearing, so that the material is not crowded and the machine is not stuffed, and the stability of the discharge molding is ensured.
The Baler machine is simple to operate and easy to use: high degree of automation, less labor, manual feeding or automatic conveyor feeding can be used.
The working principle of the Baler machine is composed of a feeding conveyor, a compressor and a discharging machine.
1. The tire baler has the characteristics of small size, light weight, low movement inertia, low noise, stable movement and flexible operation.
2. The tire baler has a wide range of applications. It can be used as a waste paper packaging equipment, but also as a processing equipment with functions such as packaging and compaction of similar products.
3. The plc configuration is coordinated with the man-machine interface (touch screen) and inspection type monitoring, and the synchronization action instruction chart is coordinated, and the length of the packet can be set.
4. The floating necking design of the tire baler in the left, right and up directions is conducive to the automatic distribution of pressure on all sides, and can be widely used for the packaging of different materials.
The tire baler produced by Nick Machinery has simple structure, convenient operation and maintenance, and low failure rate. Welcome new and old friends to come and buy 86-29-86031588
