WhatsApp:008615021631102      Email:sales@nkbaler.com       TEL:86-29-86031588

News Center

You Position : Home >> News Center
  • The sealing material is usually selected based on the chemical compatibility with the medium being transported, but even if the seal and the medium are chemically compatible, the physical interaction between them can cause the hydraulic baler to leak. Seal failure is caused by the medium drilling out of the seal and rupturing the seal from the inside. This action causes the seal to peel off or rupture, forming a leakage path. This problem is particularly serious under high temperature and high pressure, but even under less severe operating conditions Will happen too.
    According to the different reasons why air enters the waste paper baler system, the following points should be paid attention to in the use and maintenance:
    1. An exhaust valve should be installed on the upper part of the oil cylinder of the waste paper baler to facilitate the exhaust of the air in the cylinder and the system. The oil temperature change and load change that the waste paper baler adapts to are larger than the use of a throttle valve, and the application flow rate is larger. The parallel hydraulic cylinder synchronization circuit of the control valve is simple in structure and low in cost, so it is widely used.
    2. Try to prevent any pressure in the waste paper baler system from being lower than atmospheric pressure. At the same time, use a particularly good sealing device. If it fails, replace it in time. Use screws to tighten the pipe joints and all joint surfaces and clean them in time. The oil filter at the inlet of the fuel tank of the waste paper baler.

    3. Frequently check the height of the liquid oil level in the oil tank of the waste paper baler. Its height should be kept on the oil mark scale line. Separate with partitions.

    NICKBALER is an enterprise specializing in the production of hydraulic machinery and accessories. It allows you to buy one-stop and worry-free after-sales. Welcome to inquire 86-29-86031588

    2022-04-21
    Share:
  • The waste paper baler is a kind of hydraulic machinery, but as long as you follow the waste paper baler's operating rules and be careful and meticulous in your usual work, there will be no accidents. In recent years, waste paper balers have continued to suffer casualties in various places.

    According to the analysis of industry experts, the design of individual waste paper balers is unreasonable, the product quality of the manufacturer has problems, the waste paper balers are poorly maintained, the control system fails, the operators do not abide by the safety regulations, and the operators and management personnel cannot get a lot of information. Good professional training, individual or even untrained work without a license, unskilled operations or misoperation of operators are the main causes of accidents.

    Small waste paper baler is a commonly used waste paper packaging machine. With the popularization of small waste paper baler, many safety problems have also arisen during the use of small waste paper baler. Analyze the reasons, except for other subjective reasons. , As far as the small waste paper baler is concerned, there are also the following problems:
    On the one hand, there is manufacturing: mainly because manufacturers do not produce according to standards and specifications. There are two reasons for this. One is that the manufacturers themselves do not understand or understand the standards and specifications, and the other is that manufacturers are catering to the market in order to reduce costs. Cancel some safety protection devices.
    The second aspect is the use: how to use and operate the equipment correctly is very important, that is to say, the human factor is the key. Because the quality of small waste paper baler users is generally low, they lack the necessary safety knowledge and safety awareness, and safety training Insufficient efforts often result in some safety accidents.
    The third is the installation: most of the current small waste paper balers are installed by construction companies themselves. Due to weak technical force, poor personnel quality, and ignorance of standards and specifications, there are many problems in installation, so there is an urgent need to standardize management in this area. .

    NICKBALER waste paper baler as a practical machine, even if there are some objective problems, as long as we remain vigilant subjectively and always tighten the string of safe production, we will definitely be able to reduce the harm caused to us in the process of waste paper packaging. And loss.

    NICKBALER waste paper baler has the advantages of beautiful appearance, simple operation and high production efficiency. You are welcome to come and buy, contact 86-29-86031588
    2022-04-21
    Share:
  • Metal shears are currently mainly used for shearing various metal plates, and are ideal equipment for charge processing in rolling mills, non-ferrous metal plants, and smelters.
    Scrap metal is also a kind of resource, and all countries have specialized units operating the recycling and utilization of scrap metal business. The recovered scrap metal is mainly used for re-furnace smelting and converted into recycled metal.
    The scrap metal shearing machine industry is developing rapidly. The market competition is fierce. With the development of science and technology, the scale of my country's shearing machine is continuously expanding, and it is accelerating to the integration of optical and electrical machinery and automation. The scrap metal shearing machine has become my country's machinery. One of the top ten industries in the industry, but in the increasingly fierce market competition, there is still a lot of room for improvement.

    Therefore, only by constantly thinking of ways to turn the shortcomings of others into their own advantages, enterprises can survive in the cracks through continuous learning and innovation, and stand out among many manufacturers, so that they will not be eliminated and stabilized in the fierce competition. Own market position.


    NICKBALER metal shears will not produce industrial "three wastes" during use, and have no adverse effects on the environment and energy. Contact number 86-29-86031588
    2022-04-20
    Share:
  • The hydraulic baler has been widely used in the market, but in the course of use, some friends reported that the noise of the hydraulic baler occurred, which would have a great impact on the user's use in severe cases. Therefore, in order to better solve this problem, Next, we will understand the equipment noise problem.
    The hydraulic drive used by the NICKBALER hydraulic baler is stable and reliable when working, and safety is guaranteed. However, there are user reactions. During the use of the hydraulic baler, noise will be emitted, but sometimes the noise is not there. What kind of phenomenon is this? ?
    For this problem, our company has made a summary, such as the occurrence of oil trapping in the oil pump, the large error of the gear oil pump tooth profile, the jamming of the blade or the plunger, etc. will cause noise, the valve core and the valve body are not well matched, or the surface Scratching, impurity in the oil blocking the valve hole, fatigue or damage of the spring in the valve, and inflexible movement of the spool will cause noise.

    If there is a noise problem of the hydraulic baler, we must find the cause and deal with it as soon as possible, so as not to delay production and increase the cost of use. Our users should also learn more about relevant knowledge in daily use, and some minor problems should be timely. Solve it so as not to cause more trouble.

    NICKBALER has been committed to the research of various hydraulic technologies for more than ten years, and has a team with rich experience and strong technical force. 
    2022-04-20
    Share:
  • The straw briquetting machine can turn straw and sawdust into treasure, which can increase farmers' income, protect the environment, and solve the difficult problem of large garbage and straw for governments at all levels.
    The investment of straw briquetting machine is very profitable. It is a good choice to invest in building a straw recycling plant. The risk is small, the profit is large, and there must be unexpectedly rich returns.
    Investing in the construction of a straw recycling plant requires the purchase of a complete set of equipment for the briquetting machine production line, including conveyors, crushers, briquetting machines, balers, etc. Customers should purchase equipment according to their own needs and production requirements.

    Nowadays, there are more and more people using briquetting equipment, and there are many types, such as straw briquetting machine, straw briquetting machine, etc. Among them, straw briquetting machine manufacturers should pay attention to product quality issues in their daily production. And after-sales service issues, only in this way can we be invincible in the fierce competition.

    The NICKBALER straw briquetting machine is simple and convenient to operate, the machine is safe and reliable, and can be customized according to the actual needs of customers. Contact number 86-29-86031588
    2022-04-19
    Share:
Shaanxi Nick Machinery Equipment Co.,LTD 
TEL: 86-29-86031588
Fax: 86-29-86031588 Sitemap
Add: East Qunsheng Road Wuxi City,Jiangsu,China
Email:info@nkbaler.com Nickbaler888@gmail.com WhatsApp: 008615021631102  
Copyright © 2018 NKBALER .rights reserved sitemap.html
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top