Waste plastic balers are commonly used in various waste paper factories, waste recycling companies and other units and enterprises. They are suitable for packaging and recycling waste paper, plastic straws, etc., and are good equipment for improving efficiency, increasing waste, and reducing transportation costs. But, do you know the danger of high oil temperature?

1. The oil disclosure of waste plastic baler is more severe. If the pressure of the oil pump is adjusted too high, the sealing gap will increase due to the wear of the movable parts, the sealing installation will be destroyed, and the viscosity of the oil used in the waste plastic baler will increase.

2. The system has no unloading circuit or unloading circuit behaves badly. In the waste plastic baler system, there is no need to pressurize the oil. The oil is still overflowing to the fuel tank under the working pressure set by the overflow valve or to the fuel tank downstream in an environment with a relatively high unloading pressure.

3. Poor heat dissipation. Insufficient heat dissipation area of ??the fuel tank, too little oil storage in the fuel tank, causing the oil to circulate too fast, the cooling effect of the waste plastic baler cooler is poor, such as the failure of the cooling water supply or the failure of the electric fan, the surrounding air temperature is higher than the initial temperature, etc. Bad reasons.
4. Misuse of oil with too high viscosity, waste plastic baler caused excessive hydraulic loss.

Nick brand waste plastic baler has good rigidity, toughness and volatility, beautiful appearance and stingy, convenient operation and maintenance, safe and energy-saving, and low investment in equipment foundation engineering. It can better serve you.

2020-08-19

There are many popular names for automatic waste paper box baler. Common ones are: automatic hydraulic waste paper baler, horizontal automatic waste paper baler, automatic compressed waste paper baler, automatic waste paper baler, full Automatic waste paper hydraulic baler, waste paper automatic baler, automatic horizontal waste paper baler, etc. The working principle of the automatic waste paper baler: The waste paper hydraulic baler lead frame is composed of 4 sets of wire devices installed on a frame. The entire lead frame is suspended on a central axis of the compression frame, and is opposite under the action of a hydraulic motor. The compression frame moves in a horizontal direction. The compression frame is a welded component. The bottom is equipped with wheels, which can move horizontally along the main slide rail under the push of a hydraulic cylinder. The lifting platform is mainly formed by bolting two horizontal beams, and the lifting platform can move up and down in the vertical direction under the push of two hydraulic cylinders. The whole packing process consists of auxiliary time such as pressing, returning, carrying, transferring, outgoing up, outgoing down, and receiving. The main purpose of the conveyor is to provide the host with compressible raw materials in a timely manner, because manual feeding is almost impossible. The working efficiency of the main machine is high, and the insufficient supply of raw materials will reduce the efficiency of the whole machine. The conveyor of the waste paper baler works in unison with the host, and does not affect each other. When the main engine silo is full, the conveyor will automatically stop feeding and wait for the main engine to compress and pack. After the host completes a compression and packaging process, the conveyor automatically supplies waste paper. Utilizing the time gap between the two to work uninterruptedly, the overall efficiency of the equipment is improved.

The Nick brand automatic waste carton packer is simple to operate and automatically packs out, which improves work efficiency. The installation of emergency stop settings makes the operation safer.

2020-08-19

The shearing machine is suitable for metal recycling companies, scrap steel plants, smelting and foundry companies to perform cold shearing on various shapes of steel and various metal structures to add qualified charge.
The safe use of shears is as follows:
1. The shearing machine should be operated and kept by a dedicated person. It is necessary for the operator to understand the structure and function of the machine tool.
2. It is strictly forbidden to use the shearing machine with overload. It is not allowed to cut hardened steel and hard steel, high-speed steel, alloy steel, castings and non-metallic materials.
3. When the knife is operated by multiple people, there should be a special person to command, and the cooperation should be harmonious.
4. It is forbidden to cut two different standard materials together on the shearing machine, and it is forbidden to cut by stacking.
5. Prevent the handle from promoting the operation under the pressure plate when cutting the board and feeding. When cutting short material, press it with another iron plate. When cutting material, keep your fingers away from the knife edge at least 200 mm.
6. After aligning with the pry, the pry should be pulled out immediately before cutting. If the iron plate moves, use a wooden pillow to secure it to prevent the prying from popping out and hurting people after the presser foot comes down.
7. The cut workpieces must be placed stably, not piled up too high, and must not be piled up in the aisle. Remaining materials and waste materials should be sorted out in time, and the site should be tidy.

8. The safe operation of the bending machine must abide by this regulation.

Nick plate shears are recognized by many customers with high-quality qualifications and professional craftsmanship according to everyone's actual needs and are trustworthy.

2020-08-19

The automatic strapping machine does not need to insert the belt manually. The trigger mode is divided into a bit of movement, manual, continuous hitting, ball switch, foot switch, photoelectric sensor switch, just press the switch to automatically complete the packaging, convenient and fast, and can realize unmanned automatic Packing greatly saves manpower and is suitable for single machine mass production. The semi-automatic strapping machine needs to insert the strap manually. After the strap is inserted, the machine will automatically complete the strapping, bonding, cutting, and strapping process. Since each product requires manual operation, it is not suitable for mass production. 

The new circuit design makes the baler use plug-in circuit board to control the entire baling action and the temperature of the ironing head. The replacement of the circuit board is quite convenient and the baler service is convenient.

Nick brand automatic baler has simple structure, stable action, simple operation, low failure rate and easy cleaning and maintenance. It is a good helper for your production.

Shaanxi Nick Machinery Co., Ltd. is a leading manufacturer and after-sales service provider of straw baler and straw silage baler equipment in China. It is an enterprise with independent intellectual property right

2020-08-19

The electrical control part of the waste paper baler is mainly composed of PLC, motor, relay and switch electrical components. Among these parts, the most vulnerable part is the motor and electrical components. Daily precautions for the packaging electrical control box:

1. Pay attention to the grounding, lightning protection, rain protection and moisture protection of the power cord.
2. Non-professional operators of the electric control cabinet are prohibited from using it.
3. Pay attention to the anti-freezing work of the motor and the long-term overload of the motor. Effective prevention of these two can greatly reduce the damage of the motor, thereby maintaining the normal packaging of the waste paper baler.

4. Pay attention to the button operation of the console. Don't use excessive force on the switch button, and prevent misoperation to avoid short-circuit damage.

The Nick brand waste paper baler is simple to operate and automatically discharges the bale, which improves work efficiency. The installation of emergency stop settings makes the operation safer and perfect after-sales.

Shaanxi Nick Mechanical Equipment Factory specializes in the production of waste plastic balers. The advantages of waste plastic balers can be manifested in many ways. Products that can inspire customer interest can be better accepted.

2020-08-19