Instructions for use:
1. Prepare the Bailer room and wrapping cloth
2. Open the small doors on the left and right sides and the front and rear doors, spread the wrapping cloth on the bottom row, then close the door and the small door, move the small door support rods on both sides (pull the switch handle out of the hydraulic door operation), the top is small Gate.
3. Like the feeding in the box, it should be uniform and flat, not high on one side and low on the other, otherwise it will cause the pressure and discharge piston rod to tilt and bend and deform.
4. After the material box is filled, operate (pull outward) to step on the handle to lower the upper pressure row. When it drops to the yellow mark line, push the step on the handle to make the upper pressure row rise and stop when it reaches the yellow mark line.
5. Feed the material into the box again-press down-rise, repeat this several times, until the material reaches a certain weight, push the handle inward to make the upper press bar rise to the yellow mark line to stop.
6. Install the wrapping cloth on the upper pressure row, and then manipulate (pull out) the booster handle to make the stepping on the bag and the pressure cylinder simultaneously press down the pressure cylinder at the same time, and stop when the yellow marking line is overwhelmed.
7. Manipulate (push in) and press the handle to make the press bar rise to the yellow mark line to stop, and then push out the package to complete a packaging operation process.

The above is the use method of plastic film baler shared by Nick Machinery. Is it helpful to everyone? For more baler content, please pay attention to www.nkbaler.net

2021-05-25

There are different ways of discharging, such as turning the bag, pushing the bag (side pushing and forward pushing) or manually taking the bag (Bailer); all models are hydraulically driven, and manual or PLC automatic control operation can be selected;
1 No foot screws are required for installation, and diesel engines can be used as power in places where there is no power supply;
2 The size of the compression chamber and the size of the block can be customized according to customer requirements.
3 The pusher cylinder and the pusher head are connected by a spherical structure, which has good reliability and long service life of the oil seal.
4 Low noise hydraulic circuit design, high efficiency and low failure.
5 Easy to install, no foundation required.
6 button operation, PLC control, safe and reliable.

Nick Machinery can tailor the packaging machine according to your packaging requirements, space size, and budget constraints. You can contact us for more information in order to recommend the best packaging solution for you. You are welcome to consult www.nkbaler.net

2021-05-25

The waste plastic hydraulic baler is mainly suitable for the packaging of loose materials, such as waste plastic, cardboard boxes, straw, wheat straw, straw, beverage bottles, etc.
Features
1. Hydraulic configuration: The hydraulic circuit system with fast and low noise of regenerated oil adopts the combination of imported and domestic high-quality components, which not only guarantees the quality but also reduces the cost, and the performance of the whole machine is stable.
2. Electrical configuration: PLC control is selected to make the circuit simple, the failure rate is low, and the inspection and troubleshooting are simple and quick.
3. Conveyor: Conveyor belt adopts new PVC material, which is anti-corrosion and aging resistance, has the advantages of slip resistance, large conveying capacity and strong load capacity.
4. The length can be set freely, and the Bailer value can be accurately recorded.
5. Easy installation, simple foundation construction, no need for foundation reinforcement.

Nick Machinery's waste plastic baler has simple structure, easy installation, high degree of full automation, low failure rate, new and old users are welcome to come and buy www.nkbaler.net

2021-05-25

In the operation of various balers, all balers have certain safety hazards. In the operation of balers, the correct operation of the baler is the most important link, and it is also a guarantee for our own safety. I am here for everyone. Introduce the operation process of the garment Bailer machine:
1) The hydraulic oil added to the oil tank should be strictly high-quality anti-wear hydraulic oil, which must be strictly filtered, and sufficient oil should be maintained at all times, and the oil should be filled immediately if it is insufficient
(2) Each lubrication point of the machine should be filled with lubricating oil at least once per shift.  
(3) The sundries in the material box should be cleaned up in time before the baler runs.  
(4) Those who do not understand the structure, performance and operating procedures of the machine are not allowed to start the machine without learning.  
(5) When adjusting the pump, valve, and pressure gauge, it must be carried out by experienced skilled workers. If the pressure gauge is found to be faulty, the gauge should be checked or updated immediately. 
(6) The user should formulate detailed maintenance and safe operation procedures according to the specific situation.  
(7) The machine should not be overhauled or adjusted during the working process;   
(8) Do not overload or exceed the maximum eccentricity to use:   
(9) The grounding of electrical equipment must be firm and reliable:   
1. Inspection of hydraulic baler   
1. Check whether the hydraulic baler is fixed and does not move;  
2. Check whether the moving parts are lubricated;  
3. Check whether the film wire is damaged and well grounded. 
4. When the machine has serious oil leakage or abnormal phenomena during work, it should stop running immediately to analyze the cause and eliminate the fault, and it should not be forced to run with disease.
5. During the operation of the machine, no repairs or contact with moving parts are allowed, and it is strictly forbidden to press materials in the bin with hands or feet.

Nick reminds you that you must follow strict operating instructions during the use of the product, which can not only protect the safety of the operator, but also reduce the loss of the equipment and extend the service life of the equipment

2021-05-24

The hydraulic bag Baler is specially used in the textile material recycling industry. It is an ideal choice for textile manufacturers, used clothing recycling, second-hand clothing distributors, exporters, and cleaning wipes sellers.
The hydraulic carrying case balers can be widely used to compress loose materials such as cotton, chemical fiber, and hemp into bales. The hydraulic control system consists of an oil tank, gear pump set, plunger pump set, control valve station, and various execution cylinders and pipelines.
The effective volume of the oil tank is 1.8m3 and the plunger pump set are assembled parts (composed of the bottom plate, motor, oil pump, and coupling. The control valve station is divided into two groups of low pressure and high pressure. The low pressure valve station controls the hydraulic cylinder of the carrying case, the positioning hydraulic cylinder, and the lock The box and unboxing hydraulic cylinders, and the high-pressure valve station control the action of the main hydraulic cylinder.

The bag Baler produced by Nick Machinery is simple in structure, convenient in operation and maintenance, safe and reliable. It is an ideal equipment for you to compress and pack waste textiles. Welcome to buy www.nkbaler.net

2021-05-24