WhatsApp:008615021631102      Email:sales@nkbaler.com       TEL:86-29-86031588

News Center

You Position : Home >> News Center
  • Tires (such as car tires, truck tires, etc.) are ground rolling rings assembled on various vehicles or machinery
    Shaped elastic rubber products, so tires are a material with high resilience. The tire baler is specially used for
    Vertical heavy-duty dual-cylinder balers for compressing and packaging automobile tires, truck tires and other products. In design, the tires hit
    The charter plane fully considers the high degree of resilience brought about by tire compression, and especially strengthens the strength of the fuselage so that it can
    It can offset the high rebound force of the tire after compression.

    The vertical design of the tire baler has a small footprint and is widely used in tire recycling centers, which is a waste tire recycling,One of the essential machines in the industry. Using a tire baler to compress tires can greatly save storage space and reduce transportation cost.

    The standard tire baler can compress 120-140 car tires in only 9 strokes, with a compression ratio of up to 12:1 and a bale weight of 1200kg. The high-profile tire baler not only has the various performances and advantages of the standard tire baler, but also increases the cooling system and improves the hydraulic system. As far as Baler efficiency is concerned, the high-end tire Baler machine can produce a block containing 120-140 automobile tires through 7 times of feeding and compression. The machine's no-load cycle time is only 35 seconds.

    The tire bales compressed by the tire baler are widely used in the construction of sound insulation walls, urban greening facilities, and light-weight roads.

    Base filler and other civil engineering.
    If you need a high elastic material baler, you can contact us to customize your own tire baler solution www.nkbaler.com.
    2020-12-24
    Share:
  • Nick Machinery's plastic hydraulic baler is specially used for the compression and packaging of plastic films, plastic bottles, hard plastics and other plastic items. save costs,
    The suction phenomenon of the oil pump mainly refers to the mixing of air in the oil sucked by the oil pump. Excessive air mixed in the oil will cause cavitation, cavitation and noise.
    The primary reasons why the oil pump sucks in air are as follows:

    1. The oil level of the fuel tank is too low. If the oil level in the oil tank is too low, the oil flushed from the oil return pipe will agitate the oil level in the oil tank violently, air will simply mix into the oil, and the suction pipe will suck in the air bubbles.

    2. The seal is not tight. The pump's sealing ring and oil seal are ineffective, and the oil suction pipe joint is not tightly sealed. The leakage causes the lack of oil in the oil tank. At the same time, a large amount of air enters the system due to loose sealing.
    Regarding the little knowledge of the plastic hydraulic baler described by Nick Machinery, is there a good solution to help everyone? Such as
    If you have any relevant knowledge you don’t understand, you can contact us and we will give you a detailed answer. The plastic hydraulic baler produced by our company is very complete. Welcome everyone to visit and buy. www.nkbaler.com
    2020-12-18
    Share:
  • In the current market, all kinds of straw baler equipment are saturated. Many straw baler manufacturers have also racked their brains to think about marketing methods. 
    How straw baler equipment has greater competitiveness is what our manufacturers are thinking about problem.
    In the development of the entire society, the traditional straw baler equipment will eventually be replaced by the new straw baler equipment and withdraw from the market, 

    and then withdraw from the stage of history. If the straw baler equipment wants to go further, we must continue to innovate and adapt. 

    The various needs of users make the baler equipment develop better.
    Of course, we all know that innovation requires strong financial support, especially large mechanical equipment such as straw balers.
    But baler manufacturers also saw that although innovation requires our straw baler manufacturers to inject a lot of capital, this kind of effort will be rewarded. 

    Compared with the traditional straw baler exiting the market, this investment appears to be Much smaller. Therefore, it is very necessary to increase technological innovation.

    Nick Machinery is a fast-growing, mature and stable enterprise. With my country's vigorous advocacy of innovation, the technology of Nick Machinery's automatic straw hydraulic baler is constantly injected with fresh blood, which also makes Nick Machinery’s automatic straw hydraulic The baler has gradually gained experience in its development and has become a well-known brand in the fully automatic straw hydraulic baler industry.
    If you are in need of a straw baler, you can call our sales phone: 86-29-86031588, or go to our website for more detailed product information www.nkbaler.com.
    2020-12-18
    Share:
  • The metal briquetting machine produced by Nick Machinery is suitable for use in steel mills, recycling processing industries, and non-ferrous and ferrous metal smelting industries and recycling industries. With the rapid development of my country's economy, steel is also very good.
    Acceptance standards for scrap iron briquetting machine products before use
    (1) The construction acceptance of the equipment foundation of the scrap iron briquetting machine shall be checked and accepted by the quality inspector of the construction department together with the civil construction worker, and the construction acceptance form shall be filled in. The construction quality of the foundation must conform to the foundation drawing and technical requirements.
    (2) The final acceptance of the equipment installation project of the scrap iron briquetting machine shall be carried out after the equipment is qualified. The equipment management department and process technology department, together with other departments, will carry out the acceptance inspection with the participation of relevant personnel in installation, inspection, safety, and use. Make an appraisal, fill in the installation and construction quality, precision inspection, safety performance, test run record and other vouchers and acceptance handover form, signed by all parties participating in the acceptance before completion.
    (3) After passing the acceptance of the scrap iron briquetting machine equipment, go through the handover procedures: the equipment unBaler acceptance, equipment operation test record sheet signed by all parties participating in the acceptance inspection and the technical documents brought with the equipment.
    The equipment management department shall be included in the equipment file management; the spare parts storage form should be filled in with the equipment accessories and spare parts and sent to the equipment warehouse for storage. The safety management department shall file the safety issues in the installation test.
    (4) After the transfer of the scrap iron briquetting machine equipment is completed, the equipment management department will sign the equipment commissioning notice, and send the copies to the equipment management department, user unit, financial department, and production management department for archiving, notification of start of use, and fixed assets Management vouchers and the basis for evaluating the project plan.
    The metal briquetting machine produced by Nick Machinery has always had its own uniqueness, because we believe that we can only make our products more refined and distinctive. Only when users and friends are more satisfied can we have a good market for history. Make customers and friends give more praise to our metal briquetting machine.
    You are welcome to come and buy: www.nkbaler.com.
    2020-12-15
    Share:
  • The hydraulic baler has been well received since it has been put into use in the Chinese market for so many years. The low-key and stable Baler effect has made many people admire it.
    But on the other hand, the development of hydraulic balers is affected by more and more advanced science and technology. Many industries under advanced technology have begun to reform and innovate and use high-end technology to add points to their products. Hydraulic balers cannot stand still and do not seek progress. In that case It may become more and more perishing.

    Companies that have been in and out of the market for a long time will find that competition in the modern market is becoming more and more intense. Of course, more and more homogeneous products will cause more and more competition. Competition in the hydraulic baler equipment industry is also inevitable, but competition There is also a good side, that is, it stimulates hydraulic baler manufacturers to improve the quality of baling equipment.

    Therefore, packaging equipment manufacturers have also begun to actively look for new ways to improve the technical content of hydraulic packaging machines. Only by improving the quality of hydraulic packaging machines can it better adapt to the pace of current economic development and make it useful for more companies. The only way to broaden its application field is to continuously innovate and upgrade the quality and performance of the hydraulic baler.

    Step by step steadily and steadily, today’s hydraulic balers have been achieved. The current economic development is enough to make hydraulic balers develop more actively. Nick Machinery has always been very supportive of the development of hydraulic balers in our country, and we insist on reforms at all times. Innovative hydraulic baler is placed first in development.
    You are welcome to come and buy: www.nkbaler.com
    2020-12-15
    Share:
Shaanxi Nick Machinery Equipment Co.,LTD 
TEL:86-29-86031588
Fax:86-29-86031588 Sitemap
Add:East Qunsheng Road Wuxi City,Jiangsu,China
Email:info@nkbaler.com  Nickbaler888@gmail.com
WhatsApp:008615021631102 
Copyright © 2018 NKBALER .rights reserved sitemap.html
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top