WhatsApp:008615021631102      Email:sales@nkbaler.com       TEL:86-29-86031588

News Center

You Position : Home >> News Center
  • 1. The hydraulic system of the waste paper baler is the main cause of noise. For example, the valve core is caused by improper matching between the slide valve and the valve hole, or the contact between the poppet valve and the valve seat is stuck by dirt, the damping hole is blocked, the spring is skewed or invalid, etc. Stuck or cannot move in the valve hole, causing system pressure fluctuations and noise.
    2. Improper adjustment of the reversing valve of the waste paper baler makes the spool of the reversing valve move too fast, causing reversing impact, resulting in noise and vibration. 

    3. The vibrating oil pipe of the waste paper packaging machinery is slender and has many elbows without being fixed. When the oil flow passes through, especially when the flow rate is high, it is easy to cause the pipe to vibrate, the rotating parts of the motor and hydraulic pump are unbalanced, or the installation When the alignment is not good, or the coupling is loose, etc., vibration and noise can be generated.

    NICKBALER has a professional R&D design and after-sales team. If you encounter any difficult problems during use, you can contact us at any time https://www.nickbaler.net
    2022-11-07
    Share:
  • ICKBALER will share with you: How to install and debug the baler? Hope to be of some help to you. The debugging method is as follows:
    the first method:
    1. After the machine is installed, turn on the power supply of the baler, test the machine with no load, loosen the system overflow valve to make the system overflow squarely, start the motor (the method of stopping after starting), and check the direction of the motor. Can the steering be different from the oil pump sign.
    2. Start the motor and check whether the oil pump is stable and reliable during operation. There is no obvious noise in the pump, if not, stop the test machine work.
    3. Gradually adjust the relief valve handle of the waste paper hydraulic baler, so that the pressure value is about 8Mpa, and operate according to the operation sequence.
    4. Stop single action for each oil cylinder to see if it runs smoothly and without vibration, and gradually adjust the parallelism of the main pressure cylinder and side pressure cylinder with the bottom plate and side frame, fix the main pressure cylinder and side pressure cylinder, and use the adjustment support. The seat supports the rear of the cylinder.
    The second method: load test machine
    1. It is necessary to adjust the system pressure of the waste paper baler, so that the pressure value is about 20~26.5Mpa, and tighten and tighten the nut.
    2. Add material to the feeding port, use the physical packaging method for the load test, press 1~2 blocks, and hold the pressure for 3~5 seconds after the stroke of each waste paper hydraulic baler cylinder is in place, and conduct the pressure resistance test of the system.

    Testing the waste paper baler according to the above method can not only check the problems of the waste paper baler, but also solve the problems quickly, so as to ensure the quality of the waste paper baler!

    For more common sense of hydraulic baler repair and maintenance, please pay attention to the NICKBALER website https://www.nickbaler.net
    2022-11-04
    Share:
  • How can the plastic bottle baling machine tray improve the working efficiency of the plastic bottle baling machine while ensuring the baling machine quality?
    1. Select the appropriate working mode. The body material of the plastic bottle baler needs to be carefully polished, welded, oxidized, rust-proof and painted, so that the appearance is beautiful and does not fall off the paint and rust. Plastic bottle balers are mainly used in recycling and processing industries and metal smelting industries. Plastic bottle balers are mainly used for packaging and bundling of cartons, wooden boxes, paper packages and cloth packages in commercial, postal, railway, bank, food, medicine, books, distribution and other industries. The plastic bottle baler itself has many working modes: manual, jog, continuous play, ball switch, etc. Various modes are selected according to the actual operation of customers.
    2. Select the appropriate supporting equipment. The working efficiency of the plastic bottle baler is 2s/pass, so if your supporting facilities cannot supply the working speed of the waste paper baler, it is obviously a waste of time. Therefore, the supporting equipment in the front section must be efficient, so as to fully meet the working speed and load of the plastic bottle baler.
    3. Select the number of plastic bottle balers according to the production volume. The low work efficiency is sometimes not the cause of the machine itself, but it may also be a problem with the number of equipment. The daily workload of each device is certain, so when the user's output is obviously several times the number of devices, the user should consider adding devices to improve work efficiency.

    4. The work ability and familiarity of the employees will indirectly affect the work efficiency.

    For more detailed description of plastic bottle baler, you can go to NICKBALER Machinery's website https://www.nickbaler.net, or you can call our sales phone: 86-29-86031588.
    2022-11-03
    Share:
  • Whether the waste paper baler can operate normally should start from the initial installation of the baler. If the waste paper baler is not installed properly, how can it operate normally? The following are some points that should be paid attention to when installing the waste paper baler:
    1. Refer to the foundation drawing for construction and installation. If the foundation and drawings are wrong, they should be adjusted. So as not to affect the normal operation of the equipment after installation.
    2. After the host is installed, the level should be adjusted. Its level error is not greater than 0.1mm/m. It can be adjusted by angle iron, iron plate, etc. After adjusting the level, use angle iron, inclined iron and waste paper baling press machine to weld firmly.
    3. The viewing platform and the feeding port should be installed tightly and firmly. The welding port should be knocked off the welding slag, polished smooth, and sprayed with anti-rust paint.
    4. The imported wires should be buried in plastic pipes or erected at high altitudes to prevent high-voltage electric shocks. And often check the safety of the circuit, find that damage and aging need to be replaced in a timely manner.
    5. Inject 46# anti-wear waste paper baling oil (added to 80-90% of the fuel tank volume), and filter and replace the waste paper baling oil as often as required.

    6. The waste paper packaging machinery installed indoors needs to pay attention to ventilation and heat dissipation, and the outdoor installation needs to pay attention to moisture and rain.

    NICKBALER has continuously accumulated experience in the use of waste paper balers, and has mastered relevant skills and knowledge, so that waste paper balers can better complete their tasks. https://www.nickbaler.net
    2022-11-02
    Share:
  • 1. Different appearance
    The gantry shears are huge in size and are suitable for large scrap steel recycling stations. They have high work efficiency and a large amount of scrap steel. The daily output varies from 30 to 90 tons (different models of gantry shears have different output and efficiency). Crocodile shearing machine is a small equipment, suitable for self-employed, small scrap metal recycling station.
    2. The price is different
    The advantage of crocodile shears is that the price is cheap, and general shearing can meet the needs of self-employed and small scrap metal recycling stations for scrap steel processing. The gantry shears have relatively large materials and a large amount of shearing. The crocodile shearing machine is cheap in cost, small in investment, small in occupied area and low in technology.
    3. Different efficiency
    Compared with gantry shears, crocodile shears are less efficient, but they are still very worthwhile for scrap metal processing in small and medium-sized scrap metal recycling stations. The price of gantry shears is slightly higher, the cutting effect is good, labor-saving, fully automatic operation, and remote control or manual operation is also available, with high technical content.
    NICKBALER mechanical baler has the characteristics of high work efficiency, low energy consumption, easy installation and operation, safe and reliable use, strong workplace adaptability, and reasonable price. Free consultation hotline 86-29-86031588.
    4. Different scope of application
    Gantry shears are suitable for steelmaking plants, metal recycling and processing industries, non-ferrous metals, and black smelting industries. Various specifications of section steel, various metal plates and scrap metal structural parts can be cut into required specifications and sizes in cold state, which saves transportation costs and improves smelting efficiency.
    Crocodile shearing machine is suitable for metal recycling processing plants, scrapped car dismantling plants, smelting and casting industries, and cold shearing of various shapes of steel and various metal structures to process them into qualified charge. Crocodile shears can be operated continuously automatically or manually.

    Generally speaking, the plate type is more suitable for gantry shears, and the stick type is more suitable for crocodile shears. The cutting methods of the two models are different, and their suitable places are different. In short, they can make the best use of their functions.

    NICKBALER Metal Baler has the characteristics of high work efficiency, low energy consumption, easy installation and operation, safe and reliable use, strong workplace adaptability, and reasonable price. Free consultation hotline 86-29-86031588
    2022-11-01
    Share:
Shaanxi Nick Machinery Equipment Co.,LTD 
TEL:86-29-86031588
Fax:86-29-86031588 Sitemap
Add:East Qunsheng Road Wuxi City,Jiangsu,China
Email:info@nkbaler.com  Nickbaler888@gmail.com
WhatsApp:008615021631102 
Copyright © 2018 NKBALER .rights reserved sitemap.html
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top