1. In the system, the unloading circuit has a fault, or when the oil pump stops working, the unloading circuit cannot be unloaded because there is no oil unloading circuit. The total flow of the pump overflows under high pressure, and the overflow loss causes the oil to rise.
2. Select the pump supply system with the pump capacity as a quantitative according to the forward speed. The remaining flow is overheated by the overflow valve under high pressure. The selection of hydraulic components for hydraulic systems is unreasonable. When the valve is selected, the system is too hot and the system is too hot due to the standard size being too small and the loss is too high, resulting in noise. When the pump flow rate is too large, the remaining oil overflows from the relief valve, causing heat.
3. The component accuracy is not high and the equipment quality is poor. The contradiction between mechanical relative motion. The planning and construction of the hydraulic components of the system are unreasonable and the production quality is poor. When the oil passes through the valve, the pressure will disappear and the leak will be severe.
4. The system piping is too thin and too long, the winding is too long, the partial pressure loss and pressure loss are too large along the path, and there are residual hydraulic circuits or hydraulic components in the hydraulic system.
5, the part of the gap is too small, or the wear gap is too large, the internal and external leakage is too large, the volume loss is too large, such as pump power drop, heating and so on.
6. The fuel tank is too small, the heat dissipation area is not good, there is no oil cooling equipment, or the cooling equipment, the capacity is too small.
7. The viscosity of the selected oil is not suitable, the viscosity is large, the viscous resistance is large, and the viscosity increases when it is too small. In both cases, oil heating can be formed.

8. The working pressure of the hydraulic system is adjusted higher than the actual demand. Since the seal is too tight, or the seal is damaged and leaks, adjust the high pressure to work.

as more information ,please visit:  www.nkbaler.com  

2019-03-22

Shaanxi Nick Brand full range of hydraulic waste paper balers are designed to compress all types of paper, cardboard and other contractual items. It is designed as a high-performance, integrated compression device with continuous processing.
Any use outside of the above range is considered illegal. The manufacturer of the waste paper baler will not be liable for any damage caused, and the responsibility will be borne by the user. Follow the instructions for use, in accordance with the manufacturer's procedures for installation, disassembly, reorganization, start-up, operation and maintenance. Hydraulic waste paper balers can only be operated, serviced and repaired by specialists who are familiar with the operating procedures and are aware of the hazards.
Relevant accident prevention regulations and any other recognized health and safety standards should be followed.
If you want to use the equipment for work outside the scope of the contract, you must first ask the relevant technical department of Shaanxi Nick Factory, otherwise any guarantees and responsibilities of the manufacturer will be considered invalid.

2019-03-20

We know that waste paper tubes are generally more difficult to handle, but after being crushed by Shaanxi Nickel Machinery-Cardboard & Paper Tube Breaking Machine, it takes only minutes to become a piece of broken paper, rather than a general block. At the same time, the whole waste paperboard, peeling paper, paper tube, etc. can also be crushed by the cardboard & paper tube crushing machine, and then transported to the paper gas separator through the shredded paper fan pipe and dropped into the baler.
The back end of our hydraulic baler can be equipped with a block weighing system and can be connected to the whole plant production management system to truly realize the online production cost and waste paper volume.
The dust-containing gas discharged from the paper gas separator can be connected to the dust collector, and the dust removal rate can reach over 97%. The upper row or cyclone separator can also be selected according to customer requirements, and a spray device is installed for simple dust removal treatment. This design has a great purification and improvement for the workshop environment, and avoids the danger of dust explosion, and the exhaust gas also meets the national environmental emission standards.
The dust is dropped into the dust briquetting machine through a special explosion-proof discharge valve, compressed into a block-like object, which is convenient for stacking and transportation, and the workshop environment is very clean.as more information ,please visit :www.nkbaler.com 

2019-03-20

Nowadays, waste paper balers have become the products of many people. They are constantly pursuing product quality, and they are also more and more practical and intelligent. Therefore, Nick Baler Company is also in the process of research and development. Pay special attention to this detail.
First of all, the Nick Baler has a perfect hydraulic system to ensure that there is no system oil leakage during the working process. This is one of the reasons why many manufacturers have no solution at present. Secondly, the heat generated by the machine during the work leads to The machine has a high failure rate and high maintenance costs. However, the Nick Baler uses a unique cooling system, including oil-cooled equipment and water circulation equipment, so that the machine does not experience high temperatures. The above two technologies are problems that many manufacturers have no way to solve.
Secondly, at the time of electric welding, the materials are sandblasted or pickled before welding, and all the welding areas are cleaned before welding. The main fillet welds are completed by automatic or semi-automatic welding to ensure sufficient penetration. The butt welding of the steel plates is submerged arc welding to ensure penetration. Welding defects such as slag inclusions, pores, and cracks do not occur in all welds.

2019-03-18

The technology is changing, and the technology of the corresponding straw hydraulic baler needs to be continuously upgraded. The appearance and model design of the straw hydraulic baler must be continuously upgraded to maintain its position in the market. Although the change of the straw hydraulic baler requires a change in appearance, the most important thing is the inherent change of the straw hydraulic baler. The technical breakthrough is the truth.
Progress is the embodiment of things changing little by little. Only change can make progress. Progress is the condition for the development of things. Only progress can promote the development of things. The development of straw hydraulic baler industry needs to be changed little by little. Learn to change, be good at change, keep changing, straw hydraulic baler can develop, and then progress, in order to have a bigger stage. .
Straw hydraulic balers are not necessary equipment in various industries, but they have very important functions for certain industries, such as logistics, hurry, postal, etc. Its performance characteristics and technology are high-tech, which directly affects the development of these industries. It can be seen that the continuous innovation of the straw hydraulic baler technology is also a small aspect of promoting social and economic progress. The new packaging technology can usher in a new starting point, a new future, a new development direction, and also enable the straw hydraulic baler manufacturers to have more potential development and market, the physical intangible changes between the society, making the waste paper package The machine also changes itself invisibly, no matter how it changes, for the straw hydraulic baler: the inherent performance is more important than the external appearance, I hope that the majority of straw hydraulic baler manufacturers can notice this.

2019-03-15