With the increasing awareness of environmental protection, waste paper balers have played a great role. Some waste paper can be reused, and it is becoming more and more accepted by everyone. Domestic waste paper balers have been constantly innovating. , Constantly following the development of some foreign advanced technologies. In the use of the waste paper baler, moisture should be prevented from entering, so as not to affect the normal use of the waste paper baler and cause the performance of the machine to decrease. The moisture mentioned here refers to the influence of the surrounding cooling water, water vapor or moisture.
There are certain reasons to prevent the entry of moisture:
(1) Water corrodes the metal in the hydraulic system of the waste paper baler, shortening the service life of the components, and the corroded particles fall into the system, causing wear.
(2) Accelerate the deterioration of oil, especially in the presence of iron, copper, manganese and other particles, water and atmospheric oxygen quickly oxidize the oil to produce viscous polymers, commonly known as sludge. When the operating temperature exceeds 65 degrees, the oxidation speed increases, and the oxidation effect increases exponentially for every 10 degrees increase.
damage the seals and contaminate the oil, thereby causing leakage. The oil cylinder seal of the waste paper baler is made of oil-resistant rubber and other materials. The aging, cracking, and damage caused by long-term use will cause
system leakage.
If the parts are damaged by collision during the working process, the sealing element will be scratched, which can cause leakage of the waste paper baler in severe cases. The reason for the strong vibration of the waste paper baler motor is that the motor and the mechanical center driven by it are inconsistent; the coupling fails; the unit is out of balance and the foundation is not strong. In the case of the same packaging quality, it can save electricity by 50%, which greatly saves the electricity cost of the customers of the packaging station. At present, the machine has been put into market experiments and the effect has been verified. The seal selection of waste paper baler must choose high-quality well-known brands. Only good seals can delay the aging of seals.
In the use of the waste paper baler, moisture should be prevented from entering, so as not to affect the normal use of the waste paper baler and cause the performance of the machine to decrease. The moisture mentioned here refers to the influence of the surrounding cooling water, water vapor or moisture. However, the various waste paper balers appearing on the market now make many users feel dazzled. People don’t know how to choose a waste paper baler that suits them. In fact, people have not yet understood the waste paper baler. , As long as we have an understanding of his types and functions, it is not difficult to choose a suitable Baling Press.
At the same time, we have selected a Baling Press that suits you, and you must maintain it properly during use, otherwise the Baling Press will also bring us some minor troubles. Pay attention to the anti-freezing work of the motor and the long-term overload of the motor. Effective prevention of these two can greatly reduce the damage of the motor, thereby maintaining the normal packaging of the waste paper baler. Another thing is to pay attention to the button operation of the console part, do not use excessive force on the switch button, and prevent misoperation to avoid short circuit damage.
In the process of a working cycle, the empty stroke speed of the waste paper baler is generally high, and it has different movements and bears different loads in different working stages. Therefore, in the hydraulic system, the flow rate and pressure of the hydraulic pump are often determined according to the required movement speed and the load to be received during the working phase. Then, without increasing power consumption, a fast loop is used to increase the idle stroke speed of the working mechanism. The characteristic of the fast circuit is that the load is small (the pressure is small) and the flow is large. Double hydraulic pumps are now used for oil supply. The low-pressure pedestrian flow pump and the high-pressure low-flow pump are connected in parallel. They supply oil to the system at the same time to realize the rapid movement of the hydraulic cylinder. When entering the work advancement stage, the system pressure rises and the solenoid valve opens to unload the pedestrian flow pump. The small flow pump supplies oil to the system, and the movement of the oil cylinder becomes a slow-moving work stroke.
Precautions
When opening the door, people should stand in front of the machine and open the front door first, and then open the front door. When opening the door, people should stand at a 45° position on the front of the machine. People should stay away from the machine as far as possible, because the rebound force of the scissor buckle is very strong when opening the door. BigPay attention to the average, not beyond the packaging room; if it exceeds the surrounding area, it is easy to bend and deform the door, and severely crush the main body.8. After the package is finished, the strapping should be carried out. The pressure plate should be pushed to the bottom, the manual reversing valve should be set to the middle gear, press the switch, the motor will stop, and the machine door should be opened. Remember that people should stand on the side when opening the door. Stand up to prevent people from opening the door to hurt people;