WhatsApp:008615021631102      Email:sales@nkbaler.com       TEL:86-29-86031588

News Center

You Position : Home >> News Center
  • In the process of a working cycle of a straw baler, the idle stroke speed is generally high, and there are different movements and different loads in different working stages.

    Therefore, in the hydraulic system, the flow rate and pressure of the hydraulic pump are often determined according to the required movement speed and the received load during the operation stage. Then, without adding power consumption, a fast loop is selected to increase the idle travel speed of the work organization.


    The fast circuit is characterized by a small load (small pressure) and a large flow. Now use dual hydraulic pumps for oil supply. The low-pressure human flow pump and the high-pressure small flow pump are connected in parallel, and they can realize the rapid movement of the hydraulic cylinder when supplying oil to the system; when entering the work advancement stage, the system pressure rises and the solenoid valve opens to unload the human flow pump. The small flow pump supplies oil to the system, and the movement of the cylinder becomes a slow-moving stroke.

    Nick brand automatic baler has simple structure, stable action, simple operation, low failure rate and easy cleaning and maintenance. It is a good helper for your production.
    2020-08-24
    Share:
  • Some serious problems of hydraulic waste paper baler often appear some small abnormalities beforehand. Through daily protection and inspection, they will be found early, prepared early, and removed early.
    Check before starting the pump, pay attention to whether the oil tank is full of oil before starting the pump, add the oil to the upper limit indicator of the oil tank, measure the oil temperature with a thermometer, when the oil temperature is lower than 10 degrees, keep the system under no load Work for more than 20 minutes. After starting and checking the pump, start with the start and stop method. Repeat several times to increase the oil temperature. After the hydraulic equipment operates flexibly, it can enter normal operation.

    Be sure to pay attention to the noise of the pump. If the noise is too loud, check the cause and clean it before normal operation can be carried out. Check during system operation. When the system is stable, always pay attention to the oil volume, oil temperature, pressure, noise, hydraulic cylinder, motor, reversing valve, overflow valve, and pay attention to the oil leakage and oscillation of the entire system. system. After using for a period of time, if an abnormality occurs, if it cannot be removed by external adjustment, it can be differentiated for repair or replacement of accessories. Be very careful when repairing complex hydraulic components. It is best to go to a professional manufacturer for repair.

    Nick Company is a professional company engaged in the development, production, sales and service of hydraulic machinery and packaging machinery. It is your best choice to build professionalism with concentration, reputation with integrity, and sales with service.

    2020-08-24
    Share:
  • The innovation of straw balers can be in terms of function, efficiency, applicability and so on. In the modern production process, where should the innovation of straw balers start?
    1. In terms of efficiency. Straw balers have different production efficiency depending on their structure and model. For example, manual straw balers can process about 5-6 bales per hour, while automatic ones can process dozens of bales per hour. Therefore, in the future development process, the technical content of the manual baler should be further improved, and its production efficiency should be improved as much as possible.

    2. In terms of applicability. Due to the different actual production needs of some customers, the equipment composition must be relatively adjusted, such as the production volume, the size of the bag, and the requirements for incoming and outgoing materials. It is necessary to innovate the straw baler based on customer requirements and reasonable suggestions.

    The Nick brand waste paper baler is simple to operate and automatically discharges the bale, which improves work efficiency. The installation of emergency stop settings makes the operation safer and the after-sales perfect.
    2020-08-21
    Share:
  • Silage balers are widely used in various industries for the packaging of soft fiber materials and iron filings and thin iron materials, such as cotton fiber, linen, wool, clothing, cloth, towels, waste plastics, wheat straw, paper edges, waste paper boxes, tobacco , Medicinal materials, etc.
    So, how should we buy a silage baler?
    The first thing to do is to look at the brand. A good brand has stricter quality control.
    Secondly, look at the number of years the manufacturer’s machine has been developed and produced and the model of the silage baler.

    Finally, look at the structure of the silage bundling film machine, the specifications of the machine, and the degree of automation of the machine.

    Among them, the most important is the brand. Nick is a professional company engaged in the development, production, sales and service of hydraulic machinery and packaging machinery. It is your best choice to build professionalism with concentration, build reputation with integrity, and build sales with service. 
    2020-08-21
    Share:
  • The waste paper baler is simple to operate and has complete models. Today, I will teach you some solutions to the failure of the horizontal waste paper baler packaging conveyor belt.

    Check whether the machine is working normally except for automatic tape feeding. If there are no malfunctions in other parts, it is likely that there is a problem with the potentiometer. Potentiometer, on the front of the waste paper packer, there are a total of four buttons on the operation panel, from left to right are the powerswitch,potentiometer,reset button,and belt feed button.

    The potentiometer of the waste paper baler is a rotary button with a scale marked around it, which is used to control the length of the automatic belt feeding after the packing is completed. If there is more than one tape sending and the automatic sending tape is no problem, it is mostly caused by a potentiometer malfunction.
    The debugging method, turn the potentiometer to a small scale, and then fine-tune, the machine can feed the tape normally within a range. If the tape feeding is normal in a certain section of the waste paper baler, it is certain that the potentiometer is faulty.
    The next step is to replace the potentiometer. It is recommended to use a precise control potentiometer.
    The Nick brand waste paper baler is simple to operate and automatically discharges the bale, which improves work efficiency. The installation of emergency stop settings makes the operation safer and perfect after-sales.
    2020-08-21
    Share:
Shaanxi Nick Machinery Equipment Co.,LTD 
TEL: 86-29-86031588
Fax: 86-29-86031588 Sitemap
Add: East Qunsheng Road Wuxi City,Jiangsu,China
Email:info@nkbaler.com Nickbaler888@gmail.com WhatsApp: 008615021631102  
Copyright © 2018 NKBALER .rights reserved sitemap.html
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top