WhatsApp:008615021631102      Email:sales@nkbaler.com       TEL:86-29-86031588

News Center

You Position : Home >> News Center
  • One of the important reasons why aluminum cans are widely used in the world is that they are easy to recycle and reduce energy consumption. Aluminum cans are more environmentally friendly than other packaging containers. As far as the container is concerned, repeated recycling reduces environmental pollution; as far as the materials used, the repeated use of aluminum effectively saves resources and maintains the global environment. Other packaging containers, such as the popular plastics and PET materials, are all derived from petroleum. The continuous exploitation of petroleum will cause the depletion of resources. Aluminum is a rare resource on the earth. Its main source is smelting from ore. However, the electricity required to produce aluminum is far more than other metals. Compared with smelting aluminum from ore, recycling aluminum cans into aluminum can greatly reduce energy consumption and air pollution. A discarded aluminum can still exists on the surface five hundred years later and cannot be decomposed. Aluminum cans not only have the highest recyclability rate, but also the largest recycling volume, so the recycling of aluminum cans is of great significance. As a preliminary treatment of aluminum can recycling, the aluminum can bales compressed and reduced by the baler can greatly improve the convenience of storage and transportation, while maximizing storage space and transportation costs.

     Nick Machinery has a variety of Baler Compactors that can be used to compress and pack aluminum cans, vertical Baler Compactors and mini Baler Compactors, which are mainly used in the recycling industry of small and medium-sized aluminum cans. For large can recycling centers, horizontal machines are a better choice. The hopper of the horizontal baler can be matched with the conveyor, making the feeding more convenient and efficient. For more information, please contact 86-29-86031588. There is always one suitable for you.

  • (1) Those who do not understand the structure, performance and operating procedures of the machine shall not start the machine without learning.(2) Each lubrication point of the machine should be filled with lubricating oil at least once per shift.

    (3) The hydraulic oil added to the oil tank should be strictly used high-quality anti-wear hydraulic oil, which must be strictly filtered, and sufficient oil should be kept frequently, and the oil should be filled immediately when it is insufficient.

    (4) The fuel tank should be cleaned and replaced with new oil every six months, but the first cleaning and filtering of the oil should not exceed one month, and the new oil that has been used once is strictly filtered and allowed to be used again.

    (5) When there is a serious oil leak or an abnormal phenomenon occurs during work, stop immediately, analyze the cause and eliminate the fault, and do not force the operation with disease.

    (6) When the machine is running or packing, it is not allowed to repair or touch the moving parts with hands, and it is strictly forbidden to press materials in the bin with hands or feet.
    (7) When adjusting the pump, valve, and pressure gauge, it must be carried out by experienced technical workers. If the pressure gauge is found to be faulty, it should be checked or updated immediately.
    The above are the precautions for the use of NKQ series shears compiled by Nick Machinery for everyone. I hope it will be helpful to you. If you have other questions, you can pay attention to our homepage www.nkbaler.com, and we have professionals to ask you for answers.
  • Shearing machine is a kind of machine tool, which adopts hydraulic drive, reliable safety performance and convenient operation. The working blade length of the shearing machine: 400mm, 600mm, 700mm, 800mm, 1000mm, 1200mm; eight levels of shearing force from 63 tons to 400 tons, suitable for users of different scales and different requirements. No foot screws are required for installation, and diesel engines can be used as power in places where there is no power supply. The shearing machine is suitable for metal recycling processing plants, scrap car dismantling plants, smelting and casting industries. It can perform cold shearing, pressing and flanging of various shapes of steel and various metal materials. The shearing machines are divided into different types. : Metal shears, combined punching shears, hydraulic shears, bar shears. The most commonly used metal shears are alligator shears and gantry shears.

    The NKQ43 shearing machine produced by Nick Machinery has the advantages of low inertia, low noise, stable action, convenient and flexible operation, large cutting section, and convenient adjustment of the scissors mouth. It is safe to operate and easy to implement overload protection. Welcome to buy: www.nkbaler.com.

  • Before operating the straw baler, wear tight-fitting protective clothing, fasten the cuffs, and do not open the hem of the jacket. Do not wear, take off your clothes, or wrap your clothes around the machine to avoid machine damage. You must wear a safety hat, braids should be put in the hat, no skirts, slippers.
    Before the straw baler works, start the equipment idling for 3 minutes. At the same time, check whether the oil level of the fuel tank is sufficient, the sound of the oil pump is normal, and whether the hydraulic unit, pipes, joints, and pistons are leaking.
    When the bag is turned over, the handle of the cover cylinder is pulled to the return position, and then the handle is pushed in. The surrounding area of ??the package turning board shall be cleared in time every time the package is turned over to prevent jamming.
    When the straw baler is baling, the hydraulic operating handle should be quickly pushed to the designated position to prevent valve blockage and insufficient hydraulic oil flow, which may cause motor overcurrent. Every action is in place, the valve handle needs to be restored to the neutral position.
    When stopping, close the door cover, then stop the motor and cut off the power supply.

    After packing, all hydraulic rods must be retracted into the hydraulic cylinder to prevent dust from damaging the sealing ring and leaking oil.

    Regular maintenance work should be done, and if oil leaks are found in the tubing, the center immediately seeks machine repair and disposal.
    After the box cover door is opened, it is strictly forbidden to press the door to prevent accidents.
    The oil in the tank must be rigorously filtered and always maintain a sufficient amount of oil. The oil tank should be cleaned and changed every six months.
    Each smooth part of the equipment should be filled with lubricating oil at least once per shift as required, and the debris in the cavity should be cleared once per shift.
    When multiple people operate at the same time, the division of labor should be understood to prevent the risk of misoperation. Those who do not understand the main machine structure, performance and operating procedures are not allowed to start the machine without authorization.
    When the straw baler machine shows a serious oil leak or an abnormal phenomenon occurs during work, it should stop immediately. Do not look at the center of the oil radiation, do not directly remove the blockage with your hands, and do not force the operation with disease.
    When the straw baler machine is running or packing, it is not allowed to stop repairing or touch the moving parts by hand, and it is strictly forbidden to press materials in the bin with hands or feet.
    When the pumps, valves, and pressure gauges are not adjusted, they must be stopped by experienced technicians. If the pressure gauges are found to be defective, they should be repaired or replaced immediately.
    The above is the precautions of the straw baler summarized by Nick Machinery. If you have any other questions, please come to our website for consultation www.nkbaler.com.

  • (1) High speed, high efficiency and low energy consumption. Improve the working efficiency of hydraulic presses and reduce production costs.

    (2) Mechatronics and hydraulics integration. Make full and reasonable use of advanced technology in machinery and electronics to promote the improvement of the entire hydraulic system.

    (3) Automation and intelligence. The rapid development of microelectronics technology provides sufficient conditions for the automation and intelligence of hydraulic presses. Automation is not only embodied in processing, it should be able to realize automatic diagnosis and adjustment of the system, and have the function of fault pretreatment.
    (4) The hydraulic components are integrated and standardized. The integrated hydraulic system reduces pipeline connections and effectively prevents leakage and pollution. Standardized components bring convenience to the maintenance of the machine.
    Nick Machinery specializes in the production of various waste paper balers, which are suitable for waste paper recycling stations of various specifications. The waste paper baler has advanced technology, reliable quality and stable performance. If you are interested, you can follow us www.nkbaler.com, we will serve you wholeheartedly.
Shaanxi Nick Machinery Equipment Co.,LTD 
Fax:86-29-86031588 Sitemap
Add:East Qunsheng Road Wuxi City,Jiangsu,China
Email:info@nkbaler.com  Nickbaler888@gmail.com
Copyright © 2018 NKBALER .rights reserved sitemap.html
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top