The correct use, careful maintenance, and careful maintenance of waste paper packaging can help the equipment to always maintain a good working condition, reduce the occurrence of failures, and extend the service life. 
1. The operator of the semi-automatic baler should be familiar with the principle of the system, master the sequence of actions of the system and the adjustment methods of each component.  
2. Before starting the semi-automatic waste paper baler equipment, check whether all the movement mechanisms and solenoid valves are in the original state, and check the oil tank level. If the amount of oil is insufficient, the hydraulic pump is not allowed to start.  
3. The oil temperature should be controlled within the range of 35～55℃. In winter, when the temperature in the fuel tank does not reach 25°C, the sequential action of the actuators is not allowed to start. The heater should be turned on for heating, or the oil pump should be started to make the pump idling. When the oil temperature is higher than 60°C in summer, cooling measures should be taken, and the working conditions of the system should be paid close attention. If there is a problem, the pump should be stopped in time. 

4. After the gear pump of the waste paper baler is used for a long time, the relative moving surfaces of the gear will be worn and scratched. The wear of the end face causes the axial gap to increase, the wear of the addendum circle causes the radial gap to increase, and the wear of the tooth profile causes the noise to increase. Therefore, when the abrasion and strain are not serious, it can be used after a little grinding and polishing; if the abrasion and strain are serious, it needs to be repaired or replaced according to the situation.

Nick machinery production of waste paper packing machine exquisite technology, strong technical force https://www.nickbaler.net

2021-11-15

1. Before starting the machine, please add lubricating oil regularly, fixedly and quantitatively according to the lubricating chart. The lubricating oil should be clean and free of precipitation. Insist on dripping appropriate amount of lubricating oil and clean the blade surface to improve the wear resistance of the blade surface.
2. In the process of use, it is necessary to order people to strictly follow the "Scrap Shearing Machine Operating Regulations" to stop the operation, and to use the blades correctly. Normally, people must leave the machine and stop, and the operators must be trained before returning to work.
3. The blade must always be cleaned and coated with anti-rust oil. The spare blade should be stored in a cool and dry central storage. In order to prevent the blade from rusting, a layer of anti-rust oil should be applied to the blade that has been opened. The boring center ensures that the blade is not corroded.
4. Regularly check the wear and tear of the blade. If the blade is severely worn, it should be replaced in time and reported to the spare parts for supplement.
5. 10 minutes before the end of get off work every day, stop scrubbing and cleaning the blades and add oil to them. It is necessary to maintain a clean state at all times. Pay attention to avoid rust in the center without paint, and do a good job of quality work on the switch regularly.

6. During the blade transportation, you should choose a sturdy wooden box for storage, and wrap the outside with foam plastic to avoid displacement and collision during transportation. The outside of the box should be marked with "vulnerable parts" to attract attention. When unBaler the box in the workshop, use iron tools to pry and smash the wooden box to avoid damaging the cutting edge of the blade.

NICKBALER hydraulic shearer has smooth action, convenient and sensitive operation. htttps://www.nkbaler.net

2021-11-12

(1) Abrasion resistance standard
After the parts of the waste paper baler are worn out, the original structure shape and size will be changed, which will reduce the accuracy of the machine, weaken the strength, cause the parts to fail, and seriously cause the equipment to be scrapped. Among the scrapped equipment parts, most of them are caused by wear. Therefore, in the design of equipment, always strive to enhance the wear resistance of the components and reduce the wear of the components as much as possible.
(2) Vibration stability standard
There are many vibration sources that change over time on the waste paper baler, such as backlash meshing of gears, eccentric rotation of uranium, and so on. When the vibration frequency of the equipment or component is close to or equal to the frequency of the periodic interference force, resonance will occur, which is called the loss of vibration stability. Resonance not only affects the normal operation of the equipment, but also produces noise, which may cause damage to the waste paper baler.
(3) Heat resistance standard

When the parts work at high temperatures, creep occurs (the stress in the metal is constant, often low stress, but slow and continuous plastic deformation occurs), which will reduce the upper limit of its strength, the upper limit of fatigue, and destroy the normal lubrication conditions.

Nick machinery automatic horizontal paper baler equipment high technical content, quality assurance. https://www.nickbaler.net

2021-11-11

Fully automatic waste paper balers are now more equipment used in our lives and in various fields. Its appearance greatly facilitates the transportation and storage of items, thus saving companies a lot of transportation costs.
When the equipment is in use, it often encounters such problems. Among them, paper jam is a relatively common problem. So what is the cause of the paper jam in the automatic waste paper baler and how to deal with it?
1. The tape reel adjusting nut is too tight. The pulley is mainly a fixed belt roll. In the process of moving the carton, the tape roll rotates to achieve sealing, but if the tape roll cannot be rotated, the state of the cassette occurs naturally. At this time, just loosen the tape reel adjusting nut.

2. The height adjustment of the box of the automatic waste paper baler is unreasonable. The main performance of this unreasonable is that the height adjustment is too low, and the upper extension part cannot be transported through the cardboard box. At this time, you can push the carton by hand. If there is no push, the height will be higher.

Nick machine baler is a true embodiment of fast, efficient packaging. https://www.nkbaler.net

2021-11-11

1. Choose the right hydraulic oil
For the hydraulic system of an excavator, it cannot lack the support of hydraulic oil in the working process. In addition to providing power to the excavator, the hydraulic oil can also act as a lubricating and cooling device for the excavator.
Its important functions also make the quality of the hydraulic oil have an important impact on the performance of the hydraulic system. And this requires us to choose the most suitable oil quality in the process of selecting the hydraulic oil in close contact with the working environment and the specific type of the oil pump.
2. Prevent the system from entering air
In the process of using the excavator, the hydraulic system should also be prevented from entering air. If the hydraulic system enters the air, the performance of the system will be greatly affected or even many abnormal conditions such as noise, slowing down of operating speed, etc. The work intensity of the excavator will also be greatly reduced.
Therefore, during the actual use of the excavator, it is necessary to avoid placing the oil tank on the surface to prevent air from entering the hydraulic system. If air is found to enter the oil tank after the excavator is refueled, it should be the first time. To exclude.
3. Control oil pollution
The quality of the oil used by the baler will also have a greater impact on the stability of the overall system. Therefore, in order to ensure the working efficiency of the baler, it is necessary to avoid contamination of the hydraulic oil during the actual application.
In the actual use process, the independent use of different hydraulic oils should also be ensured to avoid mixing, and a filter should be placed at the inlet of the oil tank to prevent impurities such as moisture and dust from entering the system.
When the system is used for a certain period of time, it should be cleaned regularly to ensure that the impurities in the hydraulic pump and hydraulic valve can be removed in time.
4. Control the temperature of hydraulic oil
In the process of using the baler, if the hydraulic oil is overheated, its viscosity will be greatly reduced, and its lubricity will be deteriorated, which will increase the wear of the baler equipment. Both operating efficiency and operating performance will have a negative impact.

In order to avoid this situation, we need to temporarily suspend the operation after a certain period of time in the actual work process, and wait for the hydraulic oil temperature to drop to a reasonable range before proceeding with the follow-up work.

At the same time, in the process of operation, the regular cleaning of the cooling device of the Baler and the good control of the oil volume in the oil tank should also be ensured, so that the excavator can run smoothly and safely.

Nick machinery production can be designed and manufactured according to customer requirements.  https://www.nkbaler.net

2021-11-10